Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B157D  DAB (Digital Audio Broadcasting) Antenna Disconnected  


DESCRIPTION

This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna (main) which is connected to the radio receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157D DAB (Digital Audio Broadcasting) Antenna Disconnected The digital audio broadcasting antenna (main) is not connected
·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Quarter window assembly RH (window glass antenna wire and digital audio broadcasting antenna assembly)

·

Radio receiver assembly


Navigation System A

WIRING DIAGRAM

E465211E04
3.26,3.302 4.5,3.677 1.24,0.375 10 false No. 2 Antenna Cord Sub-assembly 4.667,3.281 5.865,3.688 1.198,0.406 10 false Antenna Cord Sub-assembly 6.125,3.063 7.042,3.427 0.917,0.365 10 false Radio Receiver Assembly 0.073,3.135 1.729,4.135 1.656,1 10 false Quarter Window Assembly RH (Window Glass Antenna Wire and Digital Audio Broadcasting Antenna) 1.563,0.906 1.719,1.104 0.156,0.198 10 false A 1.563,1.677 1.719,1.875 0.156,0.198 10 false A 2.99,0.906 3.146,1.104 0.156,0.198 10 false B 2.99,1.667 3.146,1.865 0.156,0.198 10 false B 5.792,0.906 6.073,1.104 0.281,0.198 10 false DB 5.802,1.677 6.083,1.875 0.281,0.198 10 false DB 1.563,0.708 1.719,0.906 0.156,0.198 10 false 1 1.531,1.469 1.771,1.656 0.24,0.188 10 false 1a 4.406,0.719 4.563,0.917 0.156,0.198 10 false 2 2.99,0.719 3.146,0.917 0.156,0.198 10 false 5 4.375,1.479 4.615,1.667 0.24,0.188 10 false 2a 2.958,1.479 3.198,1.667 0.24,0.188 10 false 5a 6.167,0.885 6.5,1.083 0.333,0.198 10 false DAB 4.406,1.677 4.563,1.875 0.156,0.198 10 false C 4.406,0.906 4.563,1.104 0.156,0.198 10 false C 5.844,0.708 6,0.906 0.156,0.198 10 false 5 5.802,1.469 6.021,1.677 0.219,0.208 10 false 5a 1.792,3.292 3.01,3.688 1.219,0.396 10 false No. 3 Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF DIGITAL AUDIO BROADCASTING ANTENNA CABLE
a.

Check if the digital audio broadcasting antenna cable is securely connected to the radio receiver assembly.

OK:

Digital audio broadcasting antenna cable is securely connected



Result:
Proceed to
OK
NG



OK

2.CHECK QUARTER WINDOW ASSEMBLY RH (WINDOW GLASS ANTENNA WIRE)

NG

SECURELY CONNECT DAB RADIO ANTENNA CABLE

2.CHECK QUARTER WINDOW ASSEMBLY RH (WINDOW GLASS ANTENNA WIRE)
a.
E111994C29
0.75,1.115 0.594,0.688 true 1.094,1.896 0.979,1.625 true 2.302,1.656 2.188,1.385 true 0.479,0.51 0.656,0.688 0.177,0.177 10 false *a 1.094,1.906 1.271,2.083 0.177,0.177 10 false *b 2.271,1.677 2.448,1.854 0.177,0.177 10 false *c
*a Tester Probe
*b Antenna Wire
*c Tin Foil


Check for continuity in the window glass antenna wire.

NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.


HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


OK:

There is continuity in the window glass antenna wire.



Result:
Proceed to
OK
NG



OK

3.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPAIR BACK WINDOW GLASS (WINDOW GLASS ANTENNA WIRE)

3.CHECK ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the antenna connector from the radio receiver assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


Procedure1

c.
E462676C02
1.583,0.177 1.875,0.406 0.292,0.229 1.573,1.844 1.865,2.073 0.292,0.229 2.198,0.958 2.427,0.208 2.427,0.208 2.51,0.208 true 1.177,2.563 1,2.094 1,2.094 0.833,2.094 true 2.146,1.688 2.031,1.688 2.031,1.688 2.135,1.167 true 1.646,0.188 1.906,0.344 0.26,0.156 10 false DB 1.677,1.875 1.844,2.042 0.167,0.167 10 false C 0.25,0.167 0.438,0.323 0.188,0.156 10 false *a 0.25,1.917 0.438,2.083 0.188,0.167 10 false *b 0.656,1.99 0.875,2.156 0.219,0.167 10 false 2a 2.573,0.115 2.958,0.313 0.385,0.198 10 false DAB 2.198,1.573 2.417,1.74 0.219,0.167 10 false 5a
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DB-5 (DAB) - C-2 Always Below 1 Ω
DB-5a - C-2a Always Below 1 Ω
DB-5 (DAB) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

4.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No.3 antenna cord sub-assembly.


Procedure1

c.
E462678C01
1.552,0.198 1.875,0.427 0.323,0.229 1.521,1.813 1.844,2.042 0.323,0.229 2.625,0.25 2.5,0.25 2.5,0.25 2.271,0.938 true 2.542,1.927 2.417,1.927 2.417,1.927 2.313,2.531 true 1.646,1.813 1.823,1.969 0.177,0.156 10 false B 1.667,0.198 1.844,0.354 0.177,0.156 10 false C 0.177,0.167 0.385,0.344 0.208,0.177 10 false *a 0.219,1.781 0.427,1.958 0.208,0.177 10 false *b 2.656,0.146 2.865,0.313 0.208,0.167 10 false 2a 2.594,1.813 2.802,1.979 0.208,0.167 10 false 5a
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - B-5 Always Below 1 Ω
C-2a - B-5a Always Below 1 Ω
C-2 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

5.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the antenna connector from the No.2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the quarter window assembly RH (window glass antenna wire and digital audio broadcasting antenna).


Procedure1

c.
E462677C01
1.552,0.198 1.875,0.427 0.323,0.229 1.521,1.813 1.844,2.042 0.323,0.229 2.625,0.25 2.5,0.25 2.5,0.25 2.313,0.813 true 2.354,3.208 2.229,3.208 2.229,3.208 1.792,2.865 true 1.646,1.813 1.823,1.969 0.177,0.156 10 false A 1.667,0.198 1.844,0.354 0.177,0.156 10 false B 0.177,0.167 0.385,0.344 0.208,0.177 10 false *a 0.219,1.781 0.427,1.958 0.208,0.177 10 false *b 2.677,0.146 2.885,0.313 0.208,0.167 10 false 5a 2.365,3.073 2.573,3.24 0.208,0.167 10 false 1a
*a Front view of wire harness connector
(to No.2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Quarter Window Assembly RH (Window Glass Antenna Wire and Digital Audio Broadcasting Antenna)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-5 - A-1 Always Below 1 Ω
B-5a - A-1a Always Below 1 Ω
B-5 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.CHECK QUARTER WINDOW ASSEMBLY RH (WINDOW GLASS ANTENNA WIRE AND DIGITAL AUDIO BROADCASTING ANTENNA)

NG

6.CHECK QUARTER WINDOW ASSEMBLY RH (WINDOW GLASS ANTENNA WIRE AND DIGITAL AUDIO BROADCASTING ANTENNA)

Pre-procedure1

a.

Replace the quarter window assembly RH (window glass antenna wire and digital audio broadcasting antenna) with a new or known good one.

HINT:

Click hereVehicle Exterior>WINDOW / GLASS>QUARTER WINDOW GLASS>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

END (WINDOW GLASS ANTENNA WIRE AND DIGITAL AUDIO BROADCASTING ANTENNA IS DEFECTIVE)

B