These DTCs are stored when a malfunction occurs in the navigation antenna assembly*1 or roof antenna assembly*2 signal lines.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C0 | Short in GPS Antenna | Navigation antenna error |
·
Antenna cord sub-assembly
·
Navigation ECU assembly
·
Radio receiver assembly
·
Navigation antenna assembly*1
·
Roof antenna assembly*2
·
No. 3 antenna cord sub-assembly*2
·
Antenna divider*3 |
Navigation System | A |
| B15C1 | Open in GPS Antenna | Error of the power source to the navigation antenna |
·
Antenna cord sub-assembly
·
Navigation ECU assembly
·
Radio receiver assembly
·
Navigation antenna assembly*1
·
Roof antenna assembly*2
·
No. 3 antenna cord sub-assembly*2
·
Antenna divider*3 |
Navigation System | A |
*1: w/o Heated windshield defroster system
*2: w/ Heated windshield defroster system
*3: w/ Heated windshield defroster system and w/ Telematics transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Pre-procedure1
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Heated Windshield Defroster System | A |
| w/ Heated Windshield Defroster System | B |
A
B
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *a | Front view of wire harness connector (to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector (to Navigation ECU Assembly) |
Disconnect the antenna connector from the navigation antenna assembly.
Disconnect the antenna connector from the navigation ECU assembly.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 - B-1 (GPS) | Always | Below 1 Ω |
| A-3a - B-1a | Always | Below 1 Ω |
| A-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Pre-procedure1
Replace the navigation ECU assembly with a known good one.
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
Pre-procedure1
Disconnect the antenna connector from the roof antenna assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Procedure1
| *a | Front view of antenna connector (to Roof Antenna Assembly) |
| *b | Front view of antenna connector (to Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 - B-2 | Always | Below 1 Ω |
| A-2a - B-2a | Always | Below 1 Ω |
| A-2 or B-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Telematics Transceiver | A |
| w/ Telematics Transceiver | B |
A
B
Pre-procedure1
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the navigation ECU assembly.
Procedure1
| *a | Front view of antenna connector (to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of antenna connector (to Navigation ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-2 - C-1 (GPS1) | Always | Below 1 Ω |
| B-2a - C-1a | Always | Below 1 Ω |
| B-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Pre-procedure1
Replace the roof antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
Pre-procedure1
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna divider.
Disconnect the antenna connector from the navigation ECU assembly.
Procedure1
| *a | Front view of antenna connector (to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of antenna connector (to Navigation ECU Assembly) |
| *c | Front view of antenna connector (to Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-2 - C-6 | Always | Below 1 Ω |
| B-2a - C-6a | Always | Below 1 Ω |
| C-2 - D-1 (GPS) | Always | Below 1 Ω |
| C-2a - D-1a | Always | Below 1 Ω |
| B-2 - Body ground | Always | 10 kΩ or higher |
| D-1 (GPS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
conditions are met C
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
| *a | Component without harness connected (Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 - 2 | Always | 10 kΩ or higher |
| 2 - 2a | Always | 243 to 267 Ω |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Replace the roof antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Pre-procedure1
Replace the antenna divider with a new or known good one.
Clear the DTCs.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL