Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2021.04–2021.07
RM38G0E _51 Engine / Hybrid System _101047 STOP AND START _0469044 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P085012  Park/Neutral Switch Circuit Short to Battery  P085014  Park/Neutral Switch Circuit Short to Ground or Open  


DESCRIPTION

The engine stop and start ECU detects malfunctions by comparing the conditions of the shift position signal and NSW signal. If a malfunction is detected, the engine stop and start ECU blinks the stop and start cancel indicator, prohibits stop and start control and stores DTC P085012 or P085014.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
P085012 Park/Neutral Switch Circuit Short to Battery Both of the following conditions are met for 15 seconds or more (2 trip detection logic):
·

Ignition switch ON

·

NSW signal is off with the shift lever in P or N


·

Park/neutral position switch assembly

·

Engine stop and start ECU

·

ECM

·

TCM

·

Wire harness or connector


Blinks SAE Code: P0852
P085014 Park/Neutral Switch Circuit Short to Ground or Open Both of the following conditions are met for 2 seconds or more (2 trip detection logic):
·

Ignition switch ON

·

NSW signal is on with the shift lever in P or N


·

Park/neutral position switch assembly

·

Engine stop and start ECU

·

ECM

·

TCM

·

Wire harness or connector


Blinks SAE Code: P0851

WIRING DIAGRAM

A436054E10
3.25,0.542 5.49,0.865 2.24,0.323 10 false from BKUP LP Fuse 0.406,1.646 2.646,1.969 2.24,0.323 10 false ECM 3.656,4.042 5.979,4.719 2.323,0.677 10 false to ST NO. 1 Relay and Certification ECU (Smart Key ECU Assembly) 5.792,4.302 6.135,4.594 0.344,0.292 10 false B38 5.781,4.438 7.156,4.865 1.375,0.427 10 false Engine Stop and Start ECU 6.208,3.552 6.552,3.844 0.344,0.292 10 false STA 6.219,0.979 6.563,1.271 0.344,0.292 10 false CLL 5.948,3.417 6.292,3.708 0.344,0.292 10 false 21 5.948,0.854 6.292,1.146 0.344,0.292 10 false 17 0.552,0.979 1.042,1.271 0.49,0.292 10 false NSW 0.792,2.656 1.281,2.948 0.49,0.292 10 false P 0.781,3.24 1.271,3.531 0.49,0.292 10 false R 0.781,3.781 1.271,4.073 0.49,0.292 10 false N 0.792,4.417 1.281,4.708 0.49,0.292 10 false D 0.125,1.5 0.615,1.792 0.49,0.292 10 false C37 4.406,1.521 4.896,1.813 0.49,0.292 10 false C34 4.406,1.688 5.74,2.115 1.333,0.427 10 false Park/Neutral Position Switch Assembly 1,0.833 1.49,1.125 0.49,0.292 10 false 7 0.99,2.573 1.479,2.865 0.49,0.292 10 false 15 1,3.146 1.49,3.438 0.49,0.292 10 false 34 0.979,3.708 1.469,4 0.49,0.292 10 false 16 1,4.281 1.49,4.573 0.49,0.292 10 false 35 1.958,2.25 2.448,2.542 0.49,0.292 10 false PL 2.438,2.26 2.927,2.552 0.49,0.292 10 false RL 2.875,2.26 3.365,2.552 0.49,0.292 10 false NL 3.354,2.271 3.844,2.563 0.49,0.292 10 false DL 3.906,2.271 4.396,2.563 0.49,0.292 10 false L 2.698,1.406 3.188,1.698 0.49,0.292 10 false RB 3.885,1.396 4.375,1.688 0.49,0.292 10 false B 2.802,1.167 3.292,1.458 0.49,0.292 10 false 2 3.906,1.177 4.396,1.469 0.49,0.292 10 false 4 2.063,2.49 2.552,2.781 0.49,0.292 10 false 6 2.521,2.5 3.01,2.792 0.49,0.292 10 false 1 2.979,2.49 3.469,2.781 0.49,0.292 10 false 9 3.438,2.5 3.927,2.792 0.49,0.292 10 false 7 3.906,2.49 4.396,2.781 0.49,0.292 10 false 5 0.375,5.063 2.615,5.385 2.24,0.323 10 false TCM 0.125,4.865 0.615,5.156 0.49,0.292 10 false C36

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Before replacing the ECM, refer to Service Bulletin (for Immobiliser System).

·

Perform Registration (VIN registration or frame number registration) after replacing the ECM.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.



PROCEDURE

1.READ VALUE USING GTS (SHIFT SW STATUS)
a.

Enter the following menus: Powertrain / Transmission / Data List / Shift SW Status (P, R, N, D Range).


b.

In accordance with the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 15,14,13,28
Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition
Shift SW Status (P Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
Shift SW Status (R Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in R
ON: Shift lever in R
Shift SW Status (N Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in N
ON: Shift lever in N
Shift SW Status (D Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in D
ON: Shift lever in D

Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (NEUTRAL POSITION SW)

NG

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.READ VALUE USING GTS (NEUTRAL POSITION SW)
a.

Enter the following menus: Powertrain / Engine / Data List / Neutral Position SW.

Powertrain > Engine > Data List
Tester Display
Neutral Position SW
50003 372 20

b.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition
Neutral Position SW Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N

Result:
Proceed to
OK
NG



OK

NG

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B38,C34)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

B38-21 (STA) - C34-5 (L) Always Below 1 Ω
B38-17 (CLL) - C34-4 (B) Always Below 1 Ω
B38-21 (STA) - Body ground Always 80 to 180 Ω
B38-17 (CLL) - Body ground Always 10 kΩ or higher
C34-5 (L) - Body ground Always 80 to 180 Ω
C34-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM, TCM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (ECM, TCM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the ECM connectors.


b.

Disconnect the TCM connectors.


c.

Disconnect the park/neutral position switch assembly connector.



Result:
Proceed to
OK
NG



OK

7.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE TCM

NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


b.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Start the engine.


b.

Perform a road test.


c.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


d.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392
Result:
Result Proceed to
DTC P080512 or P085014 is output A
DTC P085012 or P085014 is not output B




A

B

END