Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P036511  Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground  P036515  Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open  P036531  Camshaft Position Sensor "B" Bank 1 No Signal  P039011  Camshaft Position Sensor "B" Bank 2 Circuit Short to Ground  P039015  Camshaft Position Sensor "B" Bank 2 Circuit Short to Battery or Open  P039031  Camshaft Position Sensor "B" Bank 2 No Signal  


DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor (EV1, EV2 signal) consists of a magnet and MRE (Magnetoresistive Element).

The exhaust camshaft has 3 teeth on its outer circumference.

When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends the camshaft angle data to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P036511 Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft of bank 1) circuit

·

VVT sensor (for exhaust camshaft of bank 1)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


Comes on SAE: P0367
P036515 Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft of bank 1) circuit

·

VVT sensor (for exhaust camshaft of bank 1)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


Comes on SAE: P0368
P036531 Camshaft Position Sensor "B" Bank 1 No Signal There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft of bank 1) circuit

·

VVT sensor (for exhaust camshaft of bank 1)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


Comes on SAE: P0365
P039011 Camshaft Position Sensor "B" Bank 2 Circuit Short to Ground Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft of bank 2) circuit

·

VVT sensor (for exhaust camshaft of bank 2)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


Comes on SAE: P0392
P039015 Camshaft Position Sensor "B" Bank 2 Circuit Short to Battery or Open Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft of bank 2) circuit

·

VVT sensor (for exhaust camshaft of bank 2)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


Comes on SAE: P0393
P039031 Camshaft Position Sensor "B" Bank 2 No Signal There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft of bank 2) circuit

·

VVT sensor (for exhaust camshaft of bank 2)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


Comes on SAE: P0390

Reference: Inspection using an oscilloscope

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P036511, P036515, P036531, P039011, P039015 or P039031.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM


A358820E05
0.354,2.25 0.813,2.448 0.458,0.198 10 false C66 0.354,2.417 3.219,2.677 2.865,0.26 10 false VVT Sensor (for Exhaust Camshaft of Bank 1) 1.594,1.917 2.052,2.115 0.458,0.198 10 false EX- 1.563,1.385 2.021,1.583 0.458,0.198 10 false EX+ 1.563,0.854 1.896,1.052 0.333,0.198 10 false VC2 2.042,0.833 2.167,1 0.125,0.167 10 false 3 2.042,1.417 2.167,1.583 0.125,0.167 10 false 1 2.042,1.917 2.5,2.115 0.458,0.198 10 false 2 1.563,3.802 2.021,4 0.458,0.198 10 false EX+ 1.604,4.333 2.063,4.531 0.458,0.198 10 false EX- 0.333,4.635 0.792,4.833 0.458,0.198 10 false C67 0.333,4.833 3.198,5.063 2.865,0.229 10 false VVT Sensor (for Exhaust Camshaft of Bank 2) 4.458,0.833 4.917,1.031 0.458,0.198 10 false 87 4.792,0.833 5.25,1.031 0.458,0.198 10 false VCV1 4.458,1.385 4.917,1.583 0.458,0.198 10 false 90 4.792,1.385 5.25,1.583 0.458,0.198 10 false EV1+ 4.458,1.917 4.917,2.115 0.458,0.198 10 false 88 4.802,1.917 5.26,2.115 0.458,0.198 10 false VV1- 4.406,3.281 4.75,3.542 0.344,0.26 10 false 110 4.802,3.271 5.26,3.469 0.458,0.198 10 false VCV2 4.406,3.802 4.75,4.021 0.344,0.219 10 false 113 4.792,3.802 5.25,4 0.458,0.198 10 false EV2+ 4.406,4.344 4.677,4.594 0.271,0.25 10 false 111 4.792,4.333 5.25,4.531 0.458,0.198 10 false VV2- 5.333,5.219 5.792,5.417 0.458,0.198 10 false C92 5.333,5.417 5.792,5.615 0.458,0.198 10 false ECM 2,3.25 2.125,3.417 0.125,0.167 10 false 3 2,3.802 2.125,3.969 0.125,0.167 10 false 1 2,4.333 2.458,4.531 0.458,0.198 10 false 2 1.552,3.271 1.906,3.448 0.354,0.177 10 false VC2


CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (SENSOR POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C66,C92,C67)Location & Routing

Click Connector(C66)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 1 Exhaust Side)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C67)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 2 Exhaust Side)

C66-1 (EX+) - C92-90 (EV1+) Always Below 1 Ω
C66-2 (EX-) - C92-88 (VV1-) Always Below 1 Ω
C67-1 (EX+) - C92-113 (EV2+) Always Below 1 Ω
C67-2 (EX-) - C92-111 (VV2-) Always Below 1 Ω
C66-1 (EX+) or C92-90 (EV1+) - Body ground Always 10 kΩ or higher
C66-2 (EX-) or C92-88 (VV1-) - Body ground Always 10 kΩ or higher
C67-1 (EX+) or C92-113 (EV2+) - Body ground Always 10 kΩ or higher
C67-2 (EX-) or C92-111 (VV2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)
a.
A385403E03
0.354,1.792 1.271,1.99 0.917,0.198 10 false Normal 2.49,1.792 3.406,1.99 0.917,0.198 10 false Abnormal 1.5,1.563 2.677,2 1.177,0.438 10 false Clearance

Check the VVT sensor installation.

OK:

Sensor is installed correctly.


Result:
Proceed to
OK
NG




OK

4.CHECK EXHAUST CAMSHAFT

NG

4.CHECK EXHAUST CAMSHAFT
a.

Check the teeth of the camshaft.


OK:

Teeth do not have any cracks or deformation.


Result:
Proceed to
OK
NG



OK

5.REPLACE VVT SENSOR

NG

5.REPLACE VVT SENSOR

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Turn the ignition switch to ON.


b.

Clear the DTCs

Powertrain > Engine > Clear DTCs
50002 372

c.

Start the engine.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
No DTC is output A
P036511, P036515, P036531, P039011, P039015 or P039031 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B