Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P003612  HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery  P003614  HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open  P005612  HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Battery  P005614  HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Ground or Open  P102A9E  O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On  P105A9E  O2 Sensor Heater Performance Bank 2 Sensor 2 Stuck On  


DESCRIPTION

Refer to DTC P013613.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P013613

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

A287498E50
0.073,0.052 3.354,0.24 3.281,0.188 10 false Reference (System Diagram of Bank 1 Sensor 2): 0.99,1.281 2.042,1.49 1.052,0.208 10 false EFI MAIN NO.1 3.49,2.229 5.01,2.406 1.521,0.177 10 false Heated Oxygen Sensor 3.458,0.99 3.771,1.167 0.313,0.177 10 false +B 4.552,1 4.927,1.177 0.375,0.177 10 false HT1B 3.49,1.552 3.719,1.729 0.229,0.177 10 false E2 4.552,1.552 4.979,1.729 0.427,0.177 10 false OX1B 3.885,1.24 4.323,1.417 0.438,0.177 10 false Heater 3.875,1.885 4.333,2.063 0.458,0.177 10 false Sensor 5.823,3.469 6.146,3.646 0.323,0.177 10 false ECM 5.146,1 5.521,1.177 0.375,0.177 10 false HT1B 5.146,1.552 5.542,1.729 0.396,0.177 10 false OX1B 5.146,2.594 5.531,2.771 0.385,0.177 10 false EX1B 5.146,2.99 5.552,3.167 0.406,0.177 10 false MREL 0.25,1.031 0.906,1.563 0.656,0.531 10 false from SUB R/B-NO.1 Fuse 2.875,1.271 3.635,1.469 0.76,0.198 10 false EFI-B NO.2 1.958,2.396 3.01,2.604 1.052,0.208 10 false EFI MAIN NO.1


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P003612 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery Heated oxygen sensor heater current reaches high limit (1 trip detection logic).
·

Open in heated oxygen sensor (bank 1 sensor 2) heater circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

EFI MAIN NO.1 relay

·

ECM


Comes on SAE: P0038
P003614 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (bank 1 sensor 2) heater circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

EFI MAIN NO.1 relay

·

ECM


Comes on SAE: P0037
P005612 HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Battery Heated oxygen sensor heater current reaches high limit (1 trip detection logic).
·

Open in heated oxygen sensor (bank 2 sensor 2) heater circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

EFI MAIN NO.1 relay

·

ECM


Comes on SAE: P0058
P005614 HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Ground or Open Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (bank 2 sensor 2) heater circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

EFI MAIN NO.1 relay

·

ECM


Comes on SAE: P0057
P102A9E O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in heated oxygen sensor (bank 1 sensor 2) heater circuit

·

ECM


Comes on SAE: P102D
P105A9E O2 Sensor Heater Performance Bank 2 Sensor 2 Stuck On Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in heated oxygen sensor (bank 2 sensor 2) heater circuit

·

ECM


Comes on SAE: P105D

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check:

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



CONFIRMATION DRIVING PATTERN

A262623E02
0.792,0.969 1.583,1.26 0.792,0.292 10 3000 rpm 1.031,1.74 1.552,1.99 0.521,0.25 10 Idling 0.229,2.01 1.396,2.354 1.167,0.344 10 Ignition Switch ON 1.927,2.135 2.24,2.375 0.313,0.24 10 [A] 2.76,1.625 3.146,1.938 0.385,0.313 10 [B] 4.021,0.865 4.323,1.146 0.302,0.281 10 [C] 5.385,1.604 5.594,2.135 0.208,0.531 10 [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 5 minutes or more 3.854,2.615 4.458,2.854 0.604,0.24 10 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P003612, P003614, P005612, P005614, P102A9E or P105A9E.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [O2 Sensor Heater B1S2, O2 Sensor Heater B2S2, O2 Sensor Heater Current Value B1S2 and O2 Sensor Heater Current Value B2S2].

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

When the values for the Data List items O2 Sensor Heater Current Value B1S2 and O2 Sensor Heater Current Value B2S2 are not 0 A, the heaters are on.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P013613). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EFI MAIN NO.1 RELAY - HEATED OXYGEN SENSOR)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003614, P005612, P005614, P102A9E OR P105A9E)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003614, P005612, P005614, P102A9E OR P105A9E)
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


d.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P003612, P003614, P005612, P005614, P102A9E OR P105A9E is output B




A

B

5.CHECK HARNESS AND CONNECTOR (EFI MAIN NO.1 RELAY - HEATED OXYGEN SENSOR)
a.

Remove the EFI MAIN NO.1 relay.


b.

Disconnect the heated oxygen sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C85,C86)Location & Routing

Click Connector(C85)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Oxygen Sensor (Bank 1 Sensor 2)

Click Connector(C86)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 2 Oxygen Sensor (Bank 2 Sensor 2)

3 (EFI MAIN NO.1 relay) - C85-2 (+B) Always Below 1 Ω
3 (EFI MAIN NO.1 relay) - C86-2 (+B) Always Below 1 Ω
3 (EFI MAIN NO.1 relay) or C85-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
3 (EFI MAIN NO.1 relay) or C86-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR