Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P010012  Mass or Volume Air Flow Sensor "A" Circuit Short to Battery  P010014  Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection duration and to provide an appropriate air fuel ratio. Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A122492E04
1.417,0.5 1.917,1.5 false 2.615,1.073 2.271,1.5 false 4.698,1.26 4.073,2.156 false 5.031,1.552 5.521,2.198 false 0.115,0.302 1.76,0.677 1.646,0.375 10 false Temperature Sensor (Thermistor) 2.167,0.146 2.448,0.365 0.281,0.219 10 false B+ 2.208,0.542 3.573,0.781 1.365,0.24 10 false Power Transistor 2.646,0.958 4.75,1.156 2.104,0.198 10 false Platinum Hot Wire (Heater) 1.667,1.51 1.833,1.719 0.167,0.208 10 false A 2.469,1.51 2.656,1.708 0.188,0.198 10 false B 2.896,1.583 4.094,1.781 1.198,0.198 10 false Output Voltage 5.167,2.188 6.979,2.385 1.813,0.198 10 false Platinum Hot Wire (Heater) 2.896,2.188 5.417,2.396 2.521,0.208 10 false Temperature Sensor (Thermistor)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P010012 Mass or Volume Air Flow Sensor "A" Circuit Short to Battery The mass air flow meter voltage is higher than 4.9 V for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

EFI MAIN NO.1 relay

·

ECM


Comes on SAE: P0103
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open The mass air flow meter voltage is less than 0.2 V for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

EFI MAIN NO.1 relay

·

ECM


Comes on SAE: P0102

HINT:

When any of these DTCs are output, check the air flow rate by using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Mass Air Flow Sensor.

Mass Air Flow Rate (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


271.0 or more
·

Open in E2G circuit




MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter circuit and stores a DTC.

Example:

When the sensor output voltage remains less than 0.2 V, or higher than 4.9 V for 3 seconds or more, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P010012 or P010014.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A488668E02
0.594,3.917 1.083,4.167 0.49,0.25 10 false Battery 0.417,2.896 1.385,3.073 0.969,0.177 10 false SUB R/B-NO.1 1.667,0.5 1.833,0.667 0.167,0.167 10 false 5 1.677,1.552 2.667,1.75 0.99,0.198 10 false EFI MAIN NO.1 0.635,0.802 1.698,1.021 1.063,0.219 10 false EFI MAIN NO.1 2.896,0.76 3.698,0.99 0.802,0.229 10 false EFI-B NO.2 2.438,0.51 2.604,0.677 0.167,0.167 10 false 3 1.677,1.063 1.844,1.229 0.167,0.167 10 false 1 2.458,1.073 2.771,1.271 0.313,0.198 10 false 2 5.844,3.063 6.302,3.26 0.458,0.198 10 false B2 5.927,2.833 6.24,3.031 0.313,0.198 10 false 6 6.417,3.667 6.875,3.865 0.458,0.198 10 false ECM 6.167,3.052 6.781,3.25 0.615,0.198 10 false MREL 4.031,1.844 4.49,2.042 0.458,0.198 10 false C71 4.031,2.021 5.354,2.292 1.323,0.271 10 false Mass Air Flow Meter 4.104,0.5 4.417,0.698 0.313,0.198 10 false +B 3.917,0.5 4.083,0.667 0.167,0.167 10 false 3 5.313,0.813 5.479,0.979 0.167,0.167 10 false 5 5.333,1.396 5.5,1.563 0.167,0.167 10 false 4 5,0.833 5.313,1.031 0.313,0.198 10 false VG 4.917,1.417 5.333,1.583 0.417,0.167 10 false E2G 5.813,1.448 6.271,1.646 0.458,0.198 10 false C92 5.813,0.938 6.271,1.135 0.458,0.198 10 false C92 5.885,1.26 6.198,1.458 0.313,0.198 10 false 70 5.875,0.729 6.188,0.927 0.313,0.198 10 false 68 6.167,0.833 6.479,1.031 0.313,0.198 10 false VG 6.167,1.417 6.583,1.583 0.417,0.167 10 false E2G

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P010012 OR P010014)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P010014 is output A
DTC P010012 is output B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)

B

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)
a.

Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EFI MAIN NO.1 RLAY - MASS AIR FLOW METER)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the mass air flow meter.

i.

Check that the Mass Air Flow Sensor value changes when the engine is raced.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215
OK:

The reading changes.


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (EFI MAIN NO.1 RLAY - MASS AIR FLOW METER)
a.

Remove the EFI MAIN NO.1 relay.


b.

Disconnect the mass air flow meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C71)Location & Routing

Click Connector(C71)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly

3 (EFI MAIN NO.1 relay) - C71-3 (+B) Always Below 1 Ω
3 (EFI MAIN NO.1 relay) or C71-3 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C71)Location & Routing

Click Connector(C71)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly

C71-4 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR