| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C060B14 | Left Electric Parking Brake Actuator Control Circuit Short to Ground or Open |
·
Diagnosis Condition: Ignition switch ON
·
Malfunction Status: When the ECU power supply is normal, a malfunction in the electric parking brake actuator LH internal circuit is detected.
·
Detection Time: Approximately 1 second |
·
Parking brake actuator assembly LH
·
No. 2 parking brake wire assembly
·
Wire harness and connector
·
No. 2 skid control ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the Vt1 and t2 No. 2 parking brake wire assembly connectors.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(Vt1,t2)Location & Routingewd_type=routing;type=w,c;code=Vt1,t2 Click Connector(Vt1)Body>Differential Wire / Frame Wire>Frame Wire and No. 2 Parking Brake Wire Assemblyewd_type=component;type=w;code=Vt1;pinno=2,5 Click Connector(t2)Body>No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LHewd_type=component;type=c;code=t2;pinno=2,1 |
||
| Vt1-2 - t2-2 | Always | Below 1 Ω |
| Vt1-2 or t2-2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Vt1-5 - t2-1 | Always | Below 1 Ω |
| Vt1-5 or t2-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure the No. 2 parking brake wire assembly is securely installed.
Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.
Disconnect the t2 parking brake actuator assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B20,t2)Location & Routingewd_type=routing;type=c,c;code=B20,t2 Click Connector(t2)Body>No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LHewd_type=component;type=c;code=t2;pinno=2,1 |
||
| B20-3 (MRL+) - t2-2 | Always | Below 1 Ω |
| B20-3 (MRL+) or t2-2 - Body ground | Always | 10 kΩ or higher |
| B20-2 (MRL-) - t2-1 | Always | Below 1 Ω |
| B20-2 (MRL-) or t2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
NG