Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM38G0E _54 Brake _100998 PARKING BRAKE _0469398 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C060E2A  Left Electric Parking Brake Actuator Signal Stuck In Range  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C060E2A Left Electric Parking Brake Actuator Signal Stuck In Range
·

Diagnosis Condition:

Electric parking brake operating

·

Malfunction Status:

Motor locked, gear locked, free spinning

·

Detection Time:

-


·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness or connector

·

Rear brake LH


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Electric parking brake operating ○ ○ ○
Malfunction Status Motor lock detected ○ - -
Gear lock detected - ○ -
Free spinning detected - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

Although DTC C060E2A may be stored after forcibly releasing the parking brake, this is not a malfunction.

·

To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.



PROCEDURE

1.CHECK DTC
a.

Using the GTS, check for DTCs other than DTC C060E2A.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only DTC C060E2A is output A
DTCs other than C060E2A are output B



A

2.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the Vt1 and t2 No. 2 parking brake wire assembly connectors.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Vt1,t2)Location & Routing

Click Connector(Vt1)Body>Differential Wire / Frame Wire>Frame Wire and No. 2 Parking Brake Wire Assembly

Click Connector(t2)Body>No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

Vt1-2 - t2-2 Always Below 1 Ω
Vt1-2 or t2-2 - Body ground and other terminals Always 10 kΩ or higher
Vt1-5 - t2-1 Always Below 1 Ω
Vt1-5 or t2-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)
a.

Turn the ignition switch off.


b.

Make sure the No. 2 parking brake wire assembly is securely installed.


c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the t2 parking brake actuator assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20,t2)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

Click Connector(t2)Body>No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

B20-3 (MRL+) - t2-2 Always Below 1 Ω
B20-2 (MRL-) - t2-1 Always Below 1 Ω
B20-3 (MRL+) or t2-2 - Body ground Always 10 kΩ or higher
B20-2 (MRL-) or t2-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY LH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY LH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS)
a.

Check that the rotating parts are not seized or the actuator is not spinning freely.

i.

Check that the parking brake actuator assembly LH is installed properly to the rear brake caliper and that it is not spinning freely.

For the parking brake actuator assembly LH removal procedure: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


ii.

Check that there is no damage to the rotating parts from the parking brake actuator assembly LH to the rear brake caliper.


iii.

Inspect the parking brake actuator assembly LH and check that it operates correctly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


iv.

Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.

HINT:

For the check procedures, refer to the parking brake forced release method when not using SST.

Click hereBrake>PARKING BRAKE>FORCED RELEASE>OPERATION METHOD




Result:
Result Proceed to
Parking brake actuator assembly LH is malfunctioning A
Other than parking brake actuator assembly LH is malfunctioning B



A

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

B

REPAIR OR REPLACE ABNORMAL PARTS