Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C12F812  ECB Solenoid Control "A" Circuit Short to Battery  C12F814  ECB Solenoid Control "A" Circuit Short to Ground or Open  


DESCRIPTION

The main relay is built into the No. 1 skid control ECU (brake booster with master cylinder assembly).

The main relay supplies power to the switching solenoid and the linear solenoid.

The main relay remains on for approximately 3 minutes after the ignition switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C12F812 ECB Solenoid Control "A" Circuit Short to Battery The BS terminal voltage is 3.5 V or more for 4.5 seconds or more, when operation of the main relay is requested.
·

Short in main relay circuit

·

Main relay internal stuck

·

Wire harness and connector

·

Backup boost converter circuit*

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster
·

Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

·

ECB: Electronically Controlled Brake System


C12F814 ECB Solenoid Control "A" Circuit Short to Ground or Open Either of the following is detected:
·

When start the engine:

The BS terminal voltage is less than 3.3 V for 0.05 seconds or more, when the IG1 terminal voltage is 9.5 V or more and operation of the main relay is requested.

·

When the ignition switch is off:

The BS terminal voltage is less than 3.3 V for 0.05 seconds or more, when operation of the main relay is requested.


·

Open or short in main relay circuit

·

Wire harness and connector

·

Backup boost converter circuit*

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster
·

Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

·

ECB: Electronically Controlled Brake System



*: w/ Stop and Start System


C12F814 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When start the engine ○ -
When the IG1 terminal voltage is 9.5 V or more ○ -
When the ignition switch is off - ○
Malfunction Status The BS terminal voltage is less than 3.3 V and operation of the main relay is requested ○ ○
Detection Time 0.05 seconds or more. 0.05 seconds or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MAIN RELAY)
a.

Perform the Active Test and operate the main relay.


b.

Monitor the value of BS Voltage when the Active Test is being performed.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Main Relay Main relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BS Voltage BS voltage value Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to battery voltage
Chassis > Brake Booster > Active Test
Active Test Display
ECB Main Relay
Data List Display
BS Voltage
50004 466 41 295
HINT:

During the Active Test, the voltage indicated by BS Voltage changes in proportion to the voltage of the battery.



Result:
Result Proceed to
During the Active Test, the voltage indicated by BS Voltage increases to the approximate voltage of the battery. A
During the Active Test, the voltage indicated by BS Voltage remains low around 0 V. B



A

2.CLEAR DTC

B

4.CHECK VEHICLE
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
DTCs C12F812 and C12F814 are not output. A
DTCs C12F812 and/or C12F814 are output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

5.CHECK HARNESS AND CONNECTOR (+BI1 TERMINAL)

B

7.CHECK HARNESS AND CONNECTOR (+BI1 TERMINAL)
5.CHECK HARNESS AND CONNECTOR (+BI1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-14 (+BI1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-15 (BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (+BI1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-14 (+BI1) - Body ground Always 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

NG

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-15 (BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR