| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| C120200 | Master Reservoir Level Malfunction | Either of the following is detected:
·
The brake fluid level warning switch signal circuit is open for a certain period of time.
·
The reservoir level is low for a certain period of time. |
·
Open or short in brake fluid level warning switch (brake booster with master cylinder assembly)
·
Brake fluid leaks
·
Open or short in wire harness
·
Low brake fluid
·
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Brake Booster | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
|
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | - | - | - |
| Malfunction Status | The brake fluid level warning switch signal circuit is open for a certain period of time | ○ | - |
| The reservoir level is low for a certain period of time | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
Check the DTCs that are output.
| Result | Proceed to |
|---|---|
| Only C120200 is output | A |
| C120200 and other DTCs are output | B |
A
B
Check that the brake fluid level is sufficient.
If the fluid level is low, check for fluid leaks, and repair as necessary.
Check for brake fluid leaks (connection between the brake booster with accumulator pump assembly, brake master cylinder reservoir assembly (brake booster with master cylinder assembly), brake booster with master cylinder assembly, brake actuator assembly, and wheel cylinders).
If no leaks exist, add and adjust fluid using the GTS.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION
Check the thickness of the brake pad lining.
for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION
for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION
If the thickness is less than the standard, replace the brake pads with new ones.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that there are no leaks from the connections between the brake booster with accumulator pump assembly, brake booster with master cylinder assembly and brake actuator assembly.
As a visual check is very difficult, perform the check with the following procedure.
Bleed the air from the brake system.
Turn the ignition switch off.
Disconnect the B15 brake pedal stroke sensor assembly connector.
Depress the brake pedal several times to operate the pump motor, then wait until it stops.
After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ECB Motor Relay | Motor relay operation request | OFF / ON | OFF: Relay off ON: Relay on |
ECB: Electronically Controlled Brake System |
| Accumulator Pressure | Accumulator pressure output value | Min.: 0.00 MPa Max.: 24.48 MPa |
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
| Tester Display |
|---|
| ECB Motor Relay |
| Accumulator Pressure |
| Result | Proceed to |
|---|---|
| The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. | A |
| The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. | B |
Post-procedure1
None
A
B
| *a | Component without harness connected (Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly)) |
Turn the ignition switch off.
Reconnect the B15 brake pedal stroke sensor assembly connector.
Remove the brake master cylinder reservoir filler cap assembly.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the B16 brake fluid level warning switch (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
A float is located inside the brake fluid level warning switch (brake booster with master cylinder assembly). Its position changes according to the level of brake fluid.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B16)Location & Routingewd_type=routing;type=c;code=B16 |
||
| B16-1 - B16-2 | Brake fluid level warning switch (brake booster with master cylinder assembly) off (float up) | 1.84 to 2.16 kΩ |
| B16-1 - B16-2 | Brake fluid level warning switch (brake booster with master cylinder assembly) on (float down) | Below 1 Ω (Brake fluid level is low) |
If there are no problems after completing the preceding inspection, adjust the brake fluid to the MAX level with the ignition switch turned to ON.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B19,B16)Location & Routingewd_type=routing;type=c,c;code=B19,B16 |
||
| B19-12 (LBL) - B16-1 | Always | Below 1 Ω |
| B19-12 (LBL) or B16-1 - Body ground | Always | 10 kΩ or higher |
| B16-2 - Body ground | 1 minute or more after disconnecting the cable from the negative (-) battery terminal | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B16)Location & Routingewd_type=routing;type=c;code=B16 |
||
| B16-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
Turn the ignition switch off.
Reconnect the B16 brake fluid level warning switch (brake booster with master cylinder assembly) connector.
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C120200 is not output | A |
| C120200 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL