The No. 1 skid control ECU (brake booster with master cylinder assembly) stores identification information sent from other ECUs when the vehicle is shipped from the factory and changes the control constant for each system (ABS, VSC, TRC, etc.) based on the identification information.
DTC C136F00 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from those stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| C136F00 | Non-learning of the Braking System information. | Either of the following is detected:
·
The drive system information sent from the ECM does not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly).
·
No system information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly). |
·
Incorrect ECM installed
·
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Brake Booster | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
|
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | - | - | - |
| Malfunction Status | The drive system information sent from the ECM does not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) | ○ | - |
| No system information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
Check that the proper ECM is installed.
Proper ECM is installed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
Check that the proper No. 1 skid control ECU (brake booster with master cylinder assembly) is installed.
Proper No. 1 skid control ECU (brake booster with master cylinder assembly) is installed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
Perform system information memorization.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
| Tester Display |
|---|
| Reset Memory |
| Tester Display |
|---|
| Calibration |
After performing "Reset Memory" using the GTS to clear the memorized value of the No. 1 skid control ECU (brake booster with master cylinder assembly), DTC C136F00 will be stored until system information memorization is performed.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C136F00 is not output | A |
| C136F00 is output | B |
A
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL