Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C139A00  Brake Pressure Control solenoid Circuit Malfunction  C13D900  Brake Pressure Too Low (Brake Booster)  C14EC7E  Brake Pressure Control solenoid "C" Actuator Stuck On  


DESCRIPTION

The No. 1 skid control ECU (brake booster with master cylinder assembly) controls the brake fluid pressure of the master cylinder based on the output of the brake fluid pressure sensor.

DTCs may be stored if one of the following occurs:

·

Brake fluid leaks.

·

Foreign matter enters a solenoid valve.

·

Line pressure drops during air bleeding.

·

Brake pads are replaced.

·

Rotors are replaced.


HINT:

Brake pressure control solenoid "C": Solenoid SLA


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C139A00 Brake Pressure Control solenoid Circuit Malfunction Malfunction in one of the two circuits (leakage, etc.).
·

Brake fluid leaks

·

Wire harness and connector

·

Brake booster with master cylinder assembly


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
C13D900 Brake Pressure Too Low (Brake Booster) Fluid pressure control performance degraded (pressure excessively low)
·

Brake fluid leaks

·

Wire harness and connector

·

Brake booster with master cylinder assembly


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
C14EC7E Brake Pressure Control solenoid "C" Actuator Stuck On SLA valve malfunction (stuck closed, etc.)
·

Brake fluid leaks

·

Wire harness and connector

·

Brake booster with master cylinder assembly


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.


b.

Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.

Chassis > Brake Booster > Trouble Codes
50001 466
HINT:

Freeze Frame Data is only stored once when a DTC is stored.



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only C139A00, C13D900 or C14EC7E is output A
C139A00, C13D900 or C14EC7E and other DTCs are output B



A

4.CHECK FOR FLUID LEAK

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

4.CHECK FOR FLUID LEAK
a.

Based on the Freeze Frame Data or interview with the customer, inspect the following items for brake fluid leaks:

·

The brake lines from the brake booster with master cylinder assembly to each wheel cylinder.

·

The main body of the brake booster with master cylinder assembly and brake actuator assembly.


OK:

There are no fluid leaks.



Result:
Proceed to
OK
NG



OK

5.PERFORM AIR BLEEDING

NG

REPAIR OR REPLACE APPLICABLE PART

5.PERFORM AIR BLEEDING
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Perform the air bleeding procedure in Bleed Brake System.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


Result:
Proceed to
NEXT



NEXT

6.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (ACTUATOR SIDE)
6.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (ACTUATOR SIDE)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

After 3 minutes elapse after turning the ignition switch off, disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)
a.

Reconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the voltage and resistance on the wire harness side.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

OK:

Voltage and resistance readings are all normal.



Result:
Proceed to
OK
NG



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
HINT:

If the system returns to normal, it is suspected that a DTC was stored due to a poor connection of a terminal in a connector, air in the system, etc.



Result:
Result Proceed to
C139A00, C13D900 and C14EC7E are not output A
C139A00, C13D900 and/or C14EC7E are output B
C139A00 and C140A00 are output at the same time C



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY

for Brake Booster with Master Cylinder Assembly (for LHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for Brake Booster with Master Cylinder Assembly (for RHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL

for Brake Actuator Assembly (for LHD): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL

for Brake Actuator Assembly (for RHD): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL