Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C14C9A2  Electronic Brake Booster Control Module "A" System Voltage Low  


DESCRIPTION

Refer to DTC C110E14.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C110E14

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C14C9A2 Electronic Brake Booster Control Module "A" System Voltage Low The voltage of terminal +BI1 is less than 7.3 V and the pump motor is being driven, the output of the pump motor is excessively low for 1 second or more.
·

Improperly connected connector, deformation or corrosion of terminals

·

Wire harness and connector

·

Backup boost converter circuit*

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

*: w/ Stop and Start System


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only C14C9A2 is output A
C14C9A2 and other DTCs are output B



A

2.READ VALUE USING GTS (+BI1 VOLTAGE)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.READ VALUE USING GTS (+BI1 VOLTAGE)
a.

Drive the pump motor by performing the Active Test.

HINT:
·

The pump motor can be driven by performing the Active Test for ECB* solenoid (SLA).

*: Electronically Controlled Brake System

·

Perform the Active Test with the current set to maximum.




b.

Monitor the value of Data List item +BI1 Voltage when the pump motor is being driven.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Solenoid (SLA) Linear solenoid addition valve (SLA) Solenoid Start (Activate)
Solenoid SLA
(It is possible to set the current)
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BI Voltage +BI1 voltage value Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to battery voltage
Chassis > Brake Booster > Active Test
Active Test Display
ECB Solenoid (SLA)
Data List Display
BI Voltage
50004 466 43 294

Result:
Result Proceed to
+BI1 voltage is 11 to 14 V. A
+BI1 voltage is below 11 V. B



A

B

3.CHECK VEHICLE
3.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

4.CHECK HARNESS AND CONNECTOR (+BI1 AND MRI1 TERMINAL)

B

5.CHECK HARNESS AND CONNECTOR (+BI1 TERMINAL)
4.CHECK HARNESS AND CONNECTOR (+BI1 AND MRI1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-14 (+BI1) - Body ground Always 11 to 14 V
B19-1 (MRI1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (+BI1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-14 (+BI1) - Body ground Always 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MRI1 TERMINAL)

NG

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (MRI1 TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-1 (MRI1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR