Refer to DTC C110000.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C110000
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| P05DB12 | Brake Pedal Position Sensor "B" Circuit Short to Battery | The sensor output voltage 2 (SKS2) is 4.7 V or more for 0.2 seconds or more. |
·
Wire harness and connector
·
Brake pedal stroke sensor assembly |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| P05DB14 | Brake Pedal Position Sensor "B" Circuit Short to Ground or Open | The sensor output voltage 2 (SKS2) is less than 0.3 V for 0.2 seconds or more. |
·
Wire harness and connector
·
Brake pedal stroke sensor assembly |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| P05DB1F | Brake Pedal Position Sensor "B" Circuit Intermittent | The difference between the current value and previous value of the sensor output voltage 2 (SKS2) is 8.5% or more for 0.2 seconds or more. |
·
Wire harness and connector
·
Brake pedal stroke sensor assembly |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
Refer to DTC C110000.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C110000
After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
Check and adjust the brake pedal height.
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT
Adjust the brake pedal stroke sensor assembly.
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>INSTALLATION
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.
Disconnect the B15 brake pedal stroke sensor assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B20,B15)Location & Routingewd_type=routing;type=c,c;code=B20,B15 Click Connector(B15)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=B15;pinno=1 |
||
| B20-10 (SKS2) - B15-1 (SKS2) | Always | Below 1 Ω |
| B20-10 (SKS2) or B15-1 (SKS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>REMOVAL
NG