| Code | Tester Display | Measurement Item | Trouble Area | Output ECU |
|---|---|---|---|---|
| X21D2 | Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure | History of mismatch between brake pedal stroke sensor assembly and reaction force pressure sensor |
·
No. 1 skid control ECU (brake booster with master cylinder assembly)
·
Brake pedal stroke sensor assembly |
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Perform the Health Check using the GTS.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Interview the customer to check the vehicle conditions when the brake system warning light (red indicator) and brake system warning light (yellow indicator) illuminated.
Using the GTS, check for Freeze Frame Data that is recorded when a X21D2 is stored.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Freeze Frame Data is only stored once when a X21D2 is stored.
If other vehicle control history (RoB) are output, repair any malfunctions related to those vehicle control history (RoB) first, and then reproduce the conditions that caused X21D2 to be stored based on the interview with the customer.
| Proceed to |
|---|
| NEXT |
NEXT
With the brake pedal released, confirm the brake pedal stroke sensor assembly output voltage.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V Max.: 5.0 V |
Brake pedal released: 0.6 to 1.4 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Stroke Sensor |
0.6 to 1.4 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>INSTALLATION
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>INSTALLATION
Turn the ignition switch off.
Mount a pedal effort gauge.
Start the engine and depress the brake pedal once.
Depress the brake pedal after start the engine to set the vehicle to linear mode (switching solenoid (SSA) on).
Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V Max.: 5.0 V |
Brake pedal released: 0.6 to 1.4 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Stroke Sensor |
Perform this procedure in linear mode (switching solenoid (SSA) on).
| Brake Effort [N (kgf, lbf)] |
Stroke Sensor [V] |
|---|---|
| 50 (5.1, 11.2) | 1.18 to 1.88 |
| 100 (10.2, 22.5) | 1.36 to 2.06 |
| 150 (15.3, 33.7) | 1.54 to 2.24 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>REMOVAL
Depress the brake pedal slowly and check the reaction force pressure sensor output values with respect to brake pedal depression force.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reaction Force Pressure | Pressure value of stroke simulator | Min.: 0.00 MPa Max.: 24.48 MPa |
Brake pedal released: 0.00 to 1.53 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Tester Display |
|---|
| Reaction Force Pressure |
Perform this procedure in linear mode (switching solenoid (SSA) on).
| Brake Effort [N (kgf, lbf)] |
Reaction Force Pressure [MPa] |
|---|---|
| 50 (5.1, 11.2) | 0.00 to 0.71 |
| 100 (10.2, 22.5) | 0.57 to 1.37 |
| 150 (15.3, 33.7) | 1.23 to 2.03 |
| 200 (20.4, 45.0) | 1.90 to 2.70 |
| Brake Effort [N (kgf, lbf)] |
Reaction Force Pressure [MPa] |
|---|---|
| 50 (5.1, 11.2) | 0.00 to 0.71 |
| 100 (10.2, 22.5) | 0.57 to 1.37 |
| 150 (15.3, 33.7) | 1.23 to 2.03 |
| 200 (20.4, 45.0) | 1.90 to 2.70 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, clear the Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| X21D2 is not output. | A |
| X21D2 is output. | B |
A
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL