Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL PUMP
RM38G0E _51 Engine / Hybrid System _101386 1GR-FE FUEL _0470056 FUEL PUMP A

1GR-FE FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A482062N01
4.563,4.677 4.396,4.677 4.396,4.677 4.031,4.438 false 6.667,4.563 6.5,4.563 6.5,4.563 6.406,4.177 false 3.167,0.417 3.417,0.417 3.417,0.417 3.917,0.667 false 6.396,2.344 6.229,2.344 6.229,2.344 5.969,2.688 false 5.979,3.719 6.229,3.719 false 4.583,2.448 5.083,2.448 false 5.573,4.146 5.458,4.146 5.458,4.146 5.323,3.781 false 3.833,2.906 4,2.906 4,2.906 4.448,3.219 false 2.146,3.26 2.479,3.26 false 2,3.156 2.417,2.729 2.417,2.729 2.583,2.729 false 1.698,3 2.031,2.417 2.031,2.417 2.198,2.417 false 0.969,2.573 1.135,2.573 1.135,2.573 1.469,2.906 false 2.333,5.292 2.833,5.479 2.833,5.479 3,5.479 false 0.417,4.313 0.563,3.604 0.563,3.604 0.729,3.604 false 0.563,5.229 0.813,5.229 0.813,5.229 1.313,4.896 false 2.385,1.854 1.719,1.854 false 4.135,2.042 3.969,2.042 3.969,2.042 3.604,2.188 false 6.396,0.708 6.813,0.708 false 6.427,0.281 6.844,0.281 false 6.771,3.51 6.375,3.417 6.375,3.417 6.208,3.417 false 6.094,1.865 5.927,1.865 5.927,1.865 5.573,2.156 false 3.146,3.24 3.396,3.396 0.25,0.156 10 false x 2 1.271,3.708 1.521,3.865 0.25,0.156 10 false x 6 5.958,0.115 6.438,0.385 0.479,0.271 18 false 1, 2 6.208,0.552 6.469,0.823 0.26,0.271 18 false 3 6.729,4.417 6.927,4.656 0.198,0.24 18 false 4 2.979,0.26 3.25,0.542 0.271,0.281 18 false 5 6.438,2.188 6.698,2.458 0.26,0.271 18 false 6 5.813,3.573 6.073,3.844 0.26,0.271 18 false 8 4.396,2.292 4.656,2.563 0.26,0.271 18 false 9 5.896,4.01 6.219,4.281 0.323,0.271 18 false 10 3.521,2.76 3.865,3.021 0.344,0.26 18 false 11 0.667,2.417 1.01,2.677 0.344,0.26 18 false 12 2.229,2.26 2.573,2.521 0.344,0.26 18 false 13 2.604,2.573 2.948,2.833 0.344,0.26 18 false 14 2.51,3.094 2.854,3.354 0.344,0.26 18 false 15 3.042,5.313 3.385,5.573 0.344,0.26 18 false 16 0.75,3.427 1.094,3.688 0.344,0.26 18 false 17 1.531,1.771 1.771,1.938 0.24,0.167 10 false *1 4.156,1.958 4.396,2.125 0.24,0.167 10 false *2 4.604,4.583 4.844,4.75 0.24,0.167 10 false *3 0.396,5.146 0.635,5.313 0.24,0.167 10 false *4 6.01,3.271 6.271,3.542 0.26,0.271 18 false 7 6.385,1.729 6.646,2 0.26,0.271 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
4 FUEL TANK CAP ASSEMBLY 77310A - - -
5 REAR NO. 1 SEAT ASSEMBLY - - - -
6 DECK BOARD ASSEMBLY 58410B - - -
7 ROPE HOOK ASSEMBLY 66310N (Click here) - -
8 REAR FLOOR BOARD REAR LH 58418H - - -
9 REAR FLOOR BOARD REAR RH 58417B - - -
10 NO. 2 SEAT NO. 1 LEG COVER LH 79959J (Click here) - -
11 NO. 2 SEAT NO. 1 LEG COVER RH 79959G (Click here) - -
12 REAR NO. 1 SEAT PROTECTOR 71695S - - -
13 REAR NO. 2 SEAT PROTECTOR 71695T - - -
14 REAR NO. 3 SEAT PROTECTOR 71695Y - - -
15 REAR NO. 4 SEAT PROTECTOR 71F95 - - -
16 REAR DOOR SCUFF PLATE LH 67918D - - -
17 REAR DOOR SCUFF PLATE RH 67917C - - -

*1 NO. 4 REAR SIDE AIR DUCT *2 NO. 6 REAR SIDE AIR DUCT
*3 REAR FLOOR SILENCER *4 FRONT FLOOR CARPET ASSEMBLY

A482063N01
3.729,3.094 4.583,3.094 false 2.479,2.052 3.354,2.052 false 4.646,0.208 3.896,0.208 false 2.479,0.625 3.313,0.625 false 3.771,3.719 4.688,3.719 false 2.365,2.573 2.531,2.573 2.531,2.573 2.948,2.26 false 5.583,1.813 5.969,2.052 5.969,2.052 6.135,2.052 false 3.635,1.021 3.844,0.823 3.844,0.823 4.021,0.823 false 4.021,1.333 4.354,1.219 4.354,1.219 4.531,1.219 false 5.281,1.646 5.531,1.469 5.531,1.469 5.708,1.469 false 2.573,1.135 2.74,1.135 2.74,1.135 3.125,1.021 false 4.24,1.448 4.49,1.667 4.49,1.667 4.656,1.667 false 4.917,0.073 5.313,0.344 0.396,0.271 18 false 18 4.313,0.688 4.708,0.958 0.396,0.271 18 false 19 4.833,1.094 5.229,1.365 0.396,0.271 18 false 20 6.021,1.365 6.417,1.635 0.396,0.271 18 false 21 2.177,1.896 2.573,2.167 0.396,0.271 18 false 22 4.917,2.969 5.313,3.24 0.396,0.271 18 false 23 2.156,0.521 2.521,0.719 0.365,0.198 10 false ● *1 4.729,3.615 5.094,3.813 0.365,0.198 10 false ● *4 2.198,2.479 2.396,2.677 0.198,0.198 10 false *3 6.177,1.958 6.375,2.156 0.198,0.198 10 false *2 4.688,1.563 4.885,1.76 0.198,0.198 10 false *2 2.406,1.042 2.604,1.24 0.198,0.198 10 false *2

Procedure Part Name Code
Z101186

Z101188

Z101187

18 REAR FLOOR SERVICE HOLE COVER (for RH Side) 58325E (Click here) - -
19 FUEL TANK MAIN TUBE SUB-ASSEMBLY 77209C (Click here) - -
20 FUEL TANK RETURN TUBE 77204A (Click here) - -
21 NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY 77206C (Click here) - -
22 FUEL PUMP GAUGE RETAINER (for RH Side) 77144 (Click here) - -
23 FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY 77020A (Click here) - -

*1 BUTYL TAPE *2 TUBE JOINT CLIP
*3 NO. 1 FUEL TUBE CLAMP *4 GASKET
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel suction with pump and gauge tube assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of fuel pump Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 77310A 4.REMOVE FUEL TANK CAP ASSEMBLY

Hide 58410B 6.REMOVE DECK BOARD ASSEMBLY

Hide 66310N 7.REMOVE ROPE HOOK ASSEMBLY

Z101186

Click here(Click here)

Hide 58418H 8.REMOVE REAR FLOOR BOARD REAR LH

Hide 58417B 9.REMOVE REAR FLOOR BOARD REAR RH

HINT:

Use the same procedure described for the LH side.


Hide 79959J 10.REMOVE NO. 2 SEAT NO. 1 LEG COVER LH

Z101186

Click here(Click here)

Hide 79959G 11.REMOVE NO. 2 SEAT NO. 1 LEG COVER RH

Z101186

Click here(Click here)

Hide 71695S 12.REMOVE REAR NO. 1 SEAT PROTECTOR

Hide 71695T 13.REMOVE REAR NO. 2 SEAT PROTECTOR

Hide 71695Y 14.REMOVE REAR NO. 3 SEAT PROTECTOR

a.

Use the same procedure described for the rear No. 1 seat protector.


Hide 71F95 15.REMOVE REAR NO. 4 SEAT PROTECTOR

a.

Use the same procedure described for the rear No. 1 seat protector.


Hide 67918D 16.REMOVE REAR DOOR SCUFF PLATE LH

Hide 67917C 17.REMOVE REAR DOOR SCUFF PLATE RH

a.

Use the same procedure described for the LH side.


Hide 58325E 18.REMOVE REAR FLOOR SERVICE HOLE COVER (for RH Side)

a.
A482047N01
0.281,0.146 0.5,0.396 0.219,0.25 18 true i 4.021,0.188 4.24,0.438 0.219,0.25 18 true ii 0.292,2.021 0.51,2.271 0.219,0.25 18 true iii 4.021,2.042 4.24,2.292 0.219,0.25 18 true iv

i.

Detach the 6 clips and fold back the front floor carpet assembly.


ii.

Detach the 2 clips and remove the No. 4 rear side air duct and No. 6 rear side air duct.


iii.

Detach the 2 clips and fold back the rear floor silencer.


iv.

Remove the rear floor service hole cover and butyl tape.



Hide 77209C 19.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A482049C01
3.125,0.583 3.375,0.333 3.375,0.333 3.542,0.333 true 5.063,1.021 4.813,0.74 4.813,0.74 4.646,0.74 false 4.865,1.406 4.635,1.208 4.635,1.208 4.469,1.208 false 5.094,1.656 4.563,1.917 4.563,1.917 4.396,1.917 true 5.094,1.542 4.583,1.917 false 5.656,1.583 5.99,2 5.99,2 6.156,2 false 3.583,0.229 3.896,0.385 0.313,0.156 10 false *1 6.208,1.906 6.521,2.063 0.313,0.156 10 false *2 4.469,0.635 4.781,0.792 0.313,0.156 10 false *a 4.208,1.823 4.521,1.979 0.313,0.156 10 false *b 4.281,1.115 4.594,1.271 0.313,0.156 10 false *1 0.458,0.281 0.698,0.552 0.24,0.271 18 true i
*1 Tube Joint Clip *2 Fuel Suction Plate Sub-assembly
*a Fuel Tube Joint *b O-Ring


i.

Remove the tube joint clip and disconnect the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this step.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tank main tube sub-assembly.





Hide 77204A 20.DISCONNECT FUEL TANK RETURN TUBE

a.
A482050C01
5.063,1.021 4.813,0.74 4.813,0.74 4.646,0.74 false 4.865,1.406 4.635,1.208 4.635,1.208 4.469,1.208 false 5.094,1.656 4.563,1.917 4.563,1.917 4.396,1.917 true 5.094,1.542 4.583,1.917 false 5.656,1.583 5.99,2 5.99,2 6.156,2 false 0.552,1.635 0.385,1.979 0.385,1.979 0.281,1.979 false 0.104,1.885 0.417,2.042 0.313,0.156 10 false *1 6.208,1.906 6.521,2.063 0.313,0.156 10 false *2 4.469,0.635 4.781,0.792 0.313,0.156 10 false *a 4.208,1.823 4.521,1.979 0.313,0.156 10 false *b 4.281,1.115 4.594,1.271 0.313,0.156 10 false *1 0.458,0.292 0.667,0.563 0.208,0.271 18 true i
*1 Tube Joint Clip *2 Fuel Suction Plate Sub-assembly
*a Fuel Tube Joint *b O-Ring


i.

Remove the tube joint clip and disconnect the fuel tank return tube.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this step.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tank return tube.





Hide 77206C 21.DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY

a.
A482051C01
5.063,1.021 4.813,0.74 4.813,0.74 4.646,0.74 false 4.865,1.406 4.635,1.208 4.635,1.208 4.469,1.208 false 5.094,1.656 4.563,1.917 4.563,1.917 4.396,1.917 true 5.094,1.542 4.583,1.917 false 5.656,1.583 5.99,2 5.99,2 6.156,2 false 0.74,2.156 0.49,1.854 0.49,1.854 0.323,1.854 true 0.146,1.76 0.458,1.917 0.313,0.156 10 false *1 6.208,1.906 6.521,2.063 0.313,0.156 10 false *2 4.469,0.635 4.781,0.792 0.313,0.156 10 false *a 4.208,1.823 4.521,1.979 0.313,0.156 10 false *b 4.281,1.115 4.594,1.271 0.313,0.156 10 false *1 0.458,0.281 0.719,0.552 0.26,0.271 18 true i
*1 Tube Joint Clip *2 Fuel Suction Plate Sub-assembly
*a Fuel Tube Joint *b O-Ring


i.

Remove the tube joint clip and disconnect the No. 2 fuel main tube sub-assembly.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this step.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the No. 2 fuel main tube sub-assembly.





Hide 77144 22.REMOVE FUEL PUMP GAUGE RETAINER (for RH Side)

a.
A482052


b.
A482053C01
2.042,0.771 2.385,0.406 2.385,0.406 2.573,0.406 true 4.646,0.802 5.021,0.385 5.021,0.385 5.188,0.385 true 0.688,0.854 0.823,0.854 0.823,0.854 1.292,1.042 true 0.677,1.656 0.813,1.656 0.813,1.656 1.24,1.448 true 2.781,2.354 2.906,2.354 2.906,2.354 3.021,2.5 true 6.281,2.552 6.406,2.552 6.406,2.552 6.531,2.323 true 2.594,0.292 2.823,0.458 0.229,0.167 10 true *a 0.438,0.76 0.677,0.927 0.24,0.167 10 true *b 0.438,1.552 0.667,1.719 0.229,0.167 10 true *c 2.583,2.26 2.802,2.438 0.219,0.177 10 true *d 5.198,0.271 5.448,0.448 0.25,0.177 10 true *e 6.125,2.448 6.344,2.625 0.219,0.177 10 true *d 3.865,0.073 4.521,0.344 0.656,0.271 18 true iii - vi 0.396,0.073 0.813,0.375 0.417,0.302 18 true i, ii
*a SST (Plate) *b SST (Bolt)
*c SST (Claw) *d Insertion Point
*e SST (Handle) - -


i.

Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.

Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010)


iv.

Check once more that the tip of SST is securely inserted into the insertion point of the fuel pump gauge retainer.


v.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank sub-assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




vi.

While pressing down on the fuel suction with pump and gauge tube assembly, remove the fuel pump gauge retainer.



Hide 77020A 23.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A482054N01
0.427,0.208 0.656,0.469 0.229,0.26 18 true i 3.802,0.167 4.031,0.427 0.229,0.26 18 true ii

i.

Remove the fuel suction with pump and gauge tube assembly from the fuel tank sub-assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



ii.

Remove the gasket from the fuel tank sub-assembly.