| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | PRECAUTION | - | ( ) |
- | - |
| 2 | DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL | - | ( ) |
- | - |
| 3 | REAR NO. 1 SEAT ASSEMBLY RH | - | - | - | - |
| 4 | NO. 1 SEAT HEADREST ASSEMBLY LH | 71940G | - | - | - |
| *A | w/ Rear Seat Side Airbag | - | - |
| *A | w/ Rear No. 2 Seat | - | - |
| *1 | FRONT FLOOR CARPET ASSEMBLY | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear No. 1 seat assembly LH removal/installation are shown below.
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Move both front seats to the frontmost position and fold them forward.
1. PRECAUTION (w/ Rear Seat Side Airbag)
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)
|
|
for 1GR-FE:
for V35A-FTS:
3.REMOVE REAR NO. 1 SEAT ASSEMBLY RH
for 60/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)>REMOVAL
for 40/20/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 40/20/40 Split Seat Type RH Side)>REMOVAL
71940G 4.REMOVE NO. 1 SEAT HEADREST ASSEMBLY LH
71691X 5.REMOVE REAR NO. 2 SEAT CUSHION HINGE COVER
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
Place your hand at the position shown in the illustration and pull in the removal direction (1) to detach the clip and claw.
Place your hand at the position shown in the illustration and pull in the removal direction (2) to detach the clip and claw.
Pull in the removal direction (3) to detach the claw and guide to remove the rear No. 2 seat cushion hinge cover as shown in the illustration.
71692P 6.REMOVE REAR NO. 4 SEAT CUSHION HINGE COVER
Operate the reclining adjuster release handle LH and fold down the rear No. 1 seat assembly LH.
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Follow the procedure below to detach the claw.
1. Place your hand at the position shown in the illustration and pull in the removal direction (1) to detach the claw.
2. Place your hand at the position shown in the illustration and pull in the removal direction (2) to detach the claw.
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Follow the procedure below to remove the rear No. 4 seat cushion hinge cover.
1. Place your hand at the position shown in the illustration and pull in the removal direction (1) to detach the claw.
2. Place your hand at the position shown in the illustration and pull in the removal direction (2) to detach the claw and remove the rear No. 4 seat cushion hinge cover.
7.REMOVE REAR NO. 1 SEAT ASSEMBLY LH
| *A | w/ Rear Seat Side Airbag | - | - |
|
Connector |
|
Bolt |
Disconnect the connector.
w/ Rear Seat Side Airbag:
1. Disconnect the connector of the rear seat airbag assembly LH.
Do not pull while holding the wire harness.
Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR
Remove the 4 bolts.
Pull out the 2 location pins of the rear No. 1 seat assembly LH.
Remove and carry the rear No. 1 seat assembly LH out of the vehicle.
Protect the rear No. 1 seat legs.
Carrying the rear No. 1 seat assembly LH from the vehicle must be performed by multiple people.
Do not damage the rear No. 1 seat assembly LH, body exterior or interior parts.
71695S 8.REMOVE REAR NO. 1 SEAT PROTECTOR
71695T 9.REMOVE REAR NO. 2 SEAT PROTECTOR
71695Y 10.REMOVE REAR NO. 3 SEAT PROTECTOR
Use the same procedure described for the rear No. 1 seat protector.
71F95 11.REMOVE REAR NO. 4 SEAT PROTECTOR
Use the same procedure described for the rear No. 1 seat protector.
58418H 13.REMOVE REAR FLOOR BOARD LH (w/ Rear No. 2 Seat)
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>REMOVAL
58417B 14.REMOVE REAR FLOOR BOARD RH (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
79959J 15.REMOVE NO. 2 SEAT NO. 1 LEG COVER LH (w/ Rear No. 2 Seat)
79959G 16.REMOVE NO. 2 SEAT NO. 1 LEG COVER RH (w/ Rear No. 2 Seat)
72607G 17.REMOVE REAR NO. 1 SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY
| *A | w/ Rear No. 2 Seat | - | - |
|
Turn in this Direction |
|
Clip |
|
Bolt | - | - |
72607H 18.REMOVE REAR NO. 2 SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY
72607J 19.REMOVE REAR NO. 3 SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY
72607K 20.REMOVE REAR NO. 4 SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY