Refer to DTC P032511.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P032511
When DTC P032515 or P033015 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P032515 | Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open | The knock control sensor (bank 1) output voltage is higher than 4.5 V for 1 second or more (1 trip detection logic). |
·
Open or short in knock control sensor (bank 1) circuit
·
Knock control sensor (bank 1)
·
ECM |
Comes on | SAE: P0328 |
| P033015 | Knock Sensor 2 Bank 2 Circuit Short to Battery or Open | The knock control sensor (bank 2) output voltage is higher than 4.5 V for 1 second or more (1 trip detection logic). |
·
Open or short in knock control sensor (bank 2) circuit
·
Knock control sensor (bank 2)
·
ECM |
Comes on | SAE: P0333 |
Reference: Inspection using an oscilloscope.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P032511
If the output voltage transmitted by the knock control sensor remains high for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores this DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and wait 5 minutes.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P032515 or P033015.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, idle the engine for 5 minutes and check the DTC judgment result again.
Refer to DTC P032511.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P032511
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
| DTC | Suspected Area |
|---|---|
| P032515 | Bank 1 |
| P033015 | Bank 2 |
Disconnect the knock control sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C10,C9)Location & Routingewd_type=routing;type=c,c;code=C10,C9 |
||
| C10-2 - C10-1 | Ignition switch ON | 4.5 to 5.5 V |
| C9-2 - C9-1 | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>KNOCK SENSOR>INSPECTION
Perform "Inspection After Repair" after replacing the knock control sensor.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the knock control sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C10,C37,C9)Location & Routingewd_type=routing;type=c,c,c;code=C10,C37,C9 |
||
| C10-2 - C37-122 (KNK1) | Always | Below 1 Ω |
| C10-1 - C37-121 (EKNK) | Always | Below 1 Ω |
| C9-2 - C37-120 (KNK2) | Always | Below 1 Ω |
| C9-1 - C37-119 (EKN2) | Always | Below 1 Ω |
| C10-2 - C37-122 (KNK1) - Other terminals | Always | 10 kΩ or higher |
| C9-2 - C37-120 (KNK2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P032515 or P033015 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B