Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P03652A  Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range  P036531  Camshaft Position Sensor "B" Bank 1 No Signal  P039031  Camshaft Position Sensor "B" Bank 2 No Signal  


DESCRIPTION

Refer to DTC P036511.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P036511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P03652A Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range No camshaft position sensor (for exhaust camshaft of bank 1) signal to ECM while engine cranking (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft of bank 1) circuit

·

Camshaft position sensor (for exhaust camshaft of bank 1)

·

Exhaust camshaft

·

ECM


Comes on SAE: P0365
P036531 Camshaft Position Sensor "B" Bank 1 No Signal No camshaft position sensor (for exhaust camshaft of bank 1) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
*
·

Open or short in camshaft position sensor (for exhaust camshaft of bank 1) circuit

·

Camshaft position sensor (for exhaust camshaft of bank 1)

·

Exhaust camshaft

·

ECM


Comes on SAE: P0365
P039031 Camshaft Position Sensor "B" Bank 2 No Signal No camshaft position sensor (for exhaust camshaft of bank 2) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
*
·

Open or short in camshaft position sensor (for exhaust camshaft of bank 2) circuit

·

Camshaft position sensor (for exhaust camshaft of bank 2)

·

Exhaust camshaft

·

ECM


Comes on SAE: P0390

*: When the engine is being stopped or started automatically by stop and start system control, the ECM does not monitor the camshaft position sensor signal.

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P036511


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine [A].

7.

Idle the engine for 10 seconds or more [B].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P03652A, P036531 or P039031.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P03652A, P036531 Bank 1
P039031 Bank 2



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.



Result:
Proceed to
OK
NG



OK

2.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

NG

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
2.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


a.

Visually check the camshaft position sensor (for exhaust camshaft) for damage.


b.

Check the camshaft position sensor (for exhaust camshaft) installation condition.

OK:

The camshaft position sensor (for exhaust camshaft) does not have any damage and is installed properly.



Result:
Proceed to
OK
NG



OK

3.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

3.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the exhaust camshaft.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

NG

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C13,C37,C14)Location & Routing

Click Connector(C13)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 1 Exhaust Side)

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C14)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 2 Exhaust Side)

C13-1 (EX+) - C37-87 (EV1+) Always Below 1 Ω
C13-2 (EX-) - C37-65 (EV1-) Always Below 1 Ω
C13-3 (VC2) - C37-66 (VCE1) Always Below 1 Ω
C14-1 (EX+) - C37-86 (EV2+) Always Below 1 Ω
C14-2 (EX-) - C37-63 (EV2-) Always Below 1 Ω
C14-3 (VC2) - C37-64 (VCE2) Always Below 1 Ω
C13-1 (EX+) or C37-87 (EV1+) - Body ground and other terminals Always 10 kΩ or higher
C13-2 (EX-) or C37-65 (EV1-) - Body ground and other terminals Always 10 kΩ or higher
C13-3 (VC2) or C37-66 (VCE1) - Body ground and other terminals Always 10 kΩ or higher
C14-1 (EX+) or C37-86 (EV2+) - Body ground and other terminals Always 10 kΩ or higher
C14-2 (EX-) or C37-63 (EV2-) - Body ground and other terminals Always 10 kΩ or higher
C14-3 (VC2) or C37-64 (VCE2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR