Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P048014  Fan 1 Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P048012.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P048012

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P048014 Fan 1 Control Circuit Low Circuit Short to Ground or Open Open or short in fan control solenoid circuit (1 trip detection logic).
·

Open or short in fan control solenoid circuit

·

Fan control solenoid (fluid coupling assembly)

·

ECM


- SAE: P0691

MONITOR DESCRIPTION

The ECM monitors the output voltage while the fan control solenoid is operating.

The fan control solenoid turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the fan control solenoid circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine [A].

7.

Wait 2 minutes or more [B].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P048014.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [A] through [C] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY)

OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY))

NG

REPLACE FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY))
a.

Disconnect the fan control solenoid (fluid coupling assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C8)Location & Routing

Click Connector(C8)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Fluid Coupling Assembly

C8-1 (EFC+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN NO. 1 RELAY - AIR BY-PASS VALVE ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY) - ECM)
a.

Disconnect the fan control solenoid (fluid coupling assembly) connector.


b.

Disconnect the ECM connector.




OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P048014)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P048014)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P048014 is output B




A

B