Refer to DTC P008A00.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P008A00
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P008B00 | Low Pressure Fuel System Pressure - Too High | The actual fuel pressure (for low pressure side) value is higher than target fuel pressure (for low pressure side) by 200 kPa [29 psi] or more (1 trip detection logic). |
·
Fuel pump control ECU
·
No. 2 fuel pressure sensor (for low pressure side)
·
ECM |
- | SAE: P008B |
If the fuel pressure (for low pressure side) increases despite a decrease request signal being sent to the fuel pump control ECU by the ECM, the ECM will store this DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON [A].
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Drive the vehicle for 15 minutes or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P008B00.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [B] through [D] again.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P008B00 is output | A |
| P008B00 and other DTCs are output | B |
If any DTCs other than P008B00 are output, troubleshoot those DTCs first.
A
B
Start the engine.
Record the Fuel Pressure (Low) / Fuel Pressure 2 value.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Turn the ignition switch off.
Discharge the fuel pressure.
Remove the EFI MAIN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.
Start the engine.
After the engine has stopped on its own, turn the ignition switch off.
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
Crank the engine again and make sure that the engine does not start.
Install the EFI MAIN NO. 2 relay.
Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the GTS.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Perform "Inspection After Repair" after replacing the No. 2 fuel pressure sensor (for low pressure side).
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Result | Proceed to |
|---|---|
| Fuel Pressure (Low) / Fuel Pressure 2 value drops | A |
| Fuel Pressure (Low) / Fuel Pressure 2 value is maintained | B |
A
B
Install the fuel pressure gauge (for low pressure line of low pressure side).
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
Compare the values in the Data List using the GTS and the fuel pressure gauge when the Active Test was performed.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
| GTS Operation | Standard |
|---|---|
| Low | Data List value and fuel pressure gauge are within +/-50 kPa of each other |
| High |
Perform "Inspection After Repair" after replacing the No. 2 fuel pressure sensor (for low pressure side).
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the fuel pressure gauge (for low pressure line of low pressure side).
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
Read the values on the Data List and the fuel pressure gauge when the Active Test was performed.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
| GTS Operation | Fuel Pressure (Low) / Fuel Pressure 2 | Fuel Pressure Gauge | Proceed to |
|---|---|---|---|
| Low | Below 600 kPag | Below 600 kPa (6.1 kgf/cm2, 87 psi) | A |
| 600 kPag or higher | 600 kPa (6.1 kgf/cm2, 87 psi) or higher | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P008B00.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL (DTCs are not output) |
A |
| ABNORMAL (P008B00 is output) |
B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B