Refer to DTC P003312.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P003312
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P003314 | Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Ground or Open | Open or short in air by-pass valve assembly (bank 1) circuit (1 trip detection logic). |
·
Open or short in air by-pass valve assembly (bank 1) circuit
·
Air by-pass valve assembly (bank 1)
·
EFI MAIN NO. 3 relay
·
ECM |
- | SAE: P0034 |
| P00C014 | Turbocharger/Supercharger Bypass Valve "B" Control Circuit Short to Ground or Open | Open or short in air by-pass valve assembly (bank 2) circuit (1 trip detection logic). |
·
Open or short in air by-pass valve assembly (bank 2) circuit
·
Air by-pass valve assembly (bank 2)
·
EFI MAIN NO. 3 relay
·
ECM |
- | SAE: P00C1 |
The ECM monitors the output voltage while the air by-pass valve assembly is operating.
The air by-pass valve assembly turns on and off according to ON/OFF switching of a transistor inside the ECM.
If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the air by-pass valve assembly circuit and stores a DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Quickly release the accelerator pedal from the fully depressed position [C].
Enter the following menus: Powertrain / Engine / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P003314 or P00C014.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform steps [B] through [D] again.
Refer to DTC P003312.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P003312
Inspect the fuses for circuits related to this system before performing the following procedure.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
| DTC | Suspected Area |
|---|---|
| P003314 | Bank 1 |
| P00C014 | Bank 2 |
Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>INTAKE AIR CONTROL VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air by-pass valve assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C41,C42)Location & Routingewd_type=routing;type=c,c;code=C41,C42 |
||
| C41-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| C42-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air by-pass valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C41,C37,C42)Location & Routingewd_type=routing;type=c,c,c;code=C41,C37,C42 |
||
| C41-1 (ABV) - C37-30 (ABV) | Always | Below 1 Ω |
| C42-1 (ABV2) - C37-29 (ABV2) | Always | Below 1 Ω |
| C41-1 (ABV) or C37-30 (ABV) - Body ground and other terminals | Always | 10 kΩ or higher |
| C42-1 (ABV2) or C37-29 (ABV2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P003314 or P00C014.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL (DTCs are not output) |
A |
| ABNORMAL (P003314 or P00C014 is output) |
B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI MAIN NO. 3 Relay |
Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (EFI MAIN NO. 3 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI MAIN NO. 3 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the air by-pass valve assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C41,C42)Location & Routingewd_type=routing;type=c,c;code=C41,C42 |
||
| 5 (EFI MAIN NO. 3 relay) - C41-2 (+B) | Always | Below 1 Ω |
| 5 (EFI MAIN NO. 3 relay) - C42-2 (+B) | Always | Below 1 Ω |
| 5 (EFI MAIN NO. 3 relay) or C41-2 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (EFI MAIN NO. 3 relay) or C42-2 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG