Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469674 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB511  Outer Mirror Indicator (Module "A" Side) Circuit Short to Ground  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH (A) detects a short to ground in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1AB511 Outer Mirror Indicator (Module "A" Side) Circuit Short to Ground
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror RH (outer rear view mirror indicator RH)

·

Outer mirror retractor RH

·

Harness or connector

·

Outer mirror control ECU assembly RH

·

Blind spot monitor sensor RH (A)


Blind Spot Monitor "A" A

WIRING DIAGRAM

E329056E84
1.573,1.229 1.729,1.427 0.156,0.198 10 false 2 1.563,1.729 1.833,1.938 0.271,0.208 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false A 0.323,2.344 2.052,2.74 1.729,0.396 10 false Outer Mirror RH (Outer Rear View Mirror Indicator RH) 0.521,3.406 2.219,3.688 1.698,0.281 10 false Outer Mirror Retractor RH 2.948,1.156 3.198,1.344 0.25,0.188 10 false 8 2.906,1.625 3.375,1.823 0.469,0.198 10 false 12 3.083,3.406 4.656,4.083 1.573,0.677 10 false Outer Mirror Control ECU Assembly RH 3.99,1.354 4.458,1.552 0.469,0.198 10 false BDSR 4.083,1.823 4.552,2.021 0.469,0.198 10 false GND 4.563,1.344 5.031,1.542 0.469,0.198 10 false M1 4.563,1.813 5.031,2.01 0.469,0.198 10 false M1 4.563,1.146 5.031,1.344 0.469,0.198 10 false 13 4.615,1.625 5.083,1.823 0.469,0.198 10 false 7 5.969,1.365 6.438,1.563 0.469,0.198 10 false OMIR 5.781,1.24 6.25,1.438 0.469,0.198 10 false 4 5.823,3.396 6.292,3.594 0.469,0.198 10 false Q21 5.813,3.583 7.021,4.198 1.208,0.615 10 false Blind Spot Monitor Sensor RH (A) 2.917,1.333 3.719,1.698 0.802,0.365 10 false z9 3.271,1.354 3.771,1.542 0.5,0.188 10 false BSM+ 3.292,1.813 3.771,1.99 0.479,0.177 10 false BSM- 2.906,1.813 3.677,2.094 0.771,0.281 10 false z9

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor "A" > Trouble Codes
50001 461

Result:
Result Proceed to
C1AB511 is not output A
C1AB511 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] - OUTER MIRROR CONTROL ECU ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


b.

Disconnect the M1 outer mirror control ECU assembly LH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-4 (OMIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

3.INSPECT OUTER MIRROR RETRACTOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR RETRACTOR RH

Pre-procedure1

a.

Disconnect the z9 outer rear view mirror assembly RH connector.


b.

Disconnect the A outer mirror RH (outer mirror retractor RH).


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z9)Location & Routing

Click Connector(z9)Body>other>Outer Rear View Mirror Assembly RH , Outer Mirror Control ECU Assembly RH

z9-8 (BSM+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPLACE OUTER MIRROR RETRACTOR RH

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

Pre-procedure1

a.
E297461N03
1.417,1.844 1.542,1.844 1.542,1.844 1.896,1.073 true 2.458,1.833 2.333,1.833 2.333,1.833 2.167,1.302 true 1.052,1.75 1.521,1.948 0.469,0.198 10 false GND 2.552,1.719 3.021,1.917 0.469,0.198 10 false BDSR

Disconnect the outer mirror control ECU assembly RH connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13(BDSR) - 7 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

5.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

5.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

OK

NG

REPLACE OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)