Home › Engine / Hybrid System › 1GR-FE (COOLING) › WATER PUMP
RM38G0E _51 Engine / Hybrid System _101532 1GR-FE COOLING _0470522 WATER PUMP A

1GR-FE COOLING  WATER PUMP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A488717N01
4.51,0.083 6.615,1.302 2.104,1.219 4.854,0.604 5.271,0.604 false 3.958,1.729 4.375,1.729 false 3.01,1.052 3.427,1.052 false 1.833,1.156 2.25,1.156 false 1.375,2.49 1.792,2.49 false 0.573,3.24 0.99,3.24 false 0.729,4.052 1.146,4.052 false 1.417,4.438 1.833,4.438 false 4.375,4.208 4.792,4.208 false 3.906,2.458 3.906,2.208 3.906,2.208 4.073,2.208 false 3,3.271 3,3.521 3,3.521 3.25,3.521 false 4.031,2.938 4.031,3.188 4.031,3.188 4.281,3.188 false 4.844,4.083 5.125,4.375 0.281,0.292 18 false 1 3.313,3.385 3.594,3.677 0.281,0.292 18 false 3 4.656,0.469 4.938,0.76 0.281,0.292 18 false 2 3.469,0.969 3.781,1.167 0.313,0.198 10 false *4 4.417,1.646 4.729,1.844 0.313,0.198 10 false *2 1.667,1.083 1.979,1.281 0.313,0.198 10 false *5 1.198,2.417 1.51,2.615 0.313,0.198 10 false *3 0.396,3.167 0.708,3.365 0.313,0.198 10 false *1 0.552,3.969 0.865,4.167 0.313,0.198 10 false *6 1.24,4.365 1.552,4.563 0.313,0.198 10 false *7 4.333,3.094 4.49,3.281 0.156,0.188 10 false ● 4.125,2.115 4.281,2.302 0.156,0.188 10 false ● 2.573,3.406 2.833,3.604 0.26,0.198 10 false x 5 5.76,1.125 6.021,1.323 0.26,0.198 10 false x 3 4.563,0.115 4.885,0.313 0.323,0.198 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH 88310E - - -
2 AIR TUBE ASSEMBLY 17360G - - -
3 WATER INLET ASSEMBLY - - - -

*A w/ Secondary Air Injection System - -
*1 NO. 1 WATER BY-PASS HOSE *2 NO. 2 WATER BY-PASS HOSE
*3 NO. 3 WATER BY-PASS HOSE *4 NO. 4 WATER BY-PASS HOSE
*5 NO. 5 WATER BY-PASS HOSE *6 NO. 6 WATER BY-PASS HOSE
*7 NO. 7 WATER BY-PASS HOSE - -
● Non-reusable part - -

A488715N01
0.917,0.25 2.833,2 1.917,1.75 0.917,1.083 2.833,1.083 false 3.76,3.688 4.094,3.688 false 2,1.604 2,1.771 2,1.771 2.25,1.771 false 1.656,3.208 1.323,3.208 1.323,3.208 1.323,2.875 false 2.365,2.583 2.615,2.833 2.615,2.833 2.781,2.833 false 5.094,3.792 5.427,3.792 false 2.302,0.552 2.302,0.385 2.302,0.385 2.552,0.385 false 1.677,0.719 1.677,0.552 1.677,0.552 1.427,0.552 false 1.979,0.792 1.979,0.917 1.979,0.917 2.25,0.917 false 0.979,0.281 1.229,0.49 0.25,0.208 12 false *A 1,1.135 1.25,1.344 0.25,0.208 12 false *B 5.948,3.979 6.198,4.188 0.25,0.208 10 false x 4 0.823,3.031 1.073,3.24 0.25,0.208 10 false x 7 0.427,3.031 0.677,3.24 0.25,0.208 10 false x 3 0.083,2.604 0.333,2.813 0.25,0.208 10 false x 2 0.323,2.219 0.573,2.427 0.25,0.208 10 false x 5 2.323,1.646 2.594,1.938 0.271,0.292 18 false 4 2.302,0.792 2.573,1.083 0.271,0.292 18 false 4 4.927,3.667 5.198,3.958 0.271,0.292 18 false 5 4.156,3.563 4.427,3.854 0.271,0.292 18 false 6 1.729,3.094 2,3.385 0.271,0.292 18 false 7 2.844,2.74 3.021,2.927 0.177,0.188 10 false ● 1.25,0.469 1.5,0.677 0.25,0.208 10 false *2 2.594,0.313 2.792,0.49 0.198,0.177 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

4 NO. 2 IDLER PULLEY SUB-ASSEMBLY 16604 - - -
5 V-RIBBED BELT TENSIONER ASSEMBLY 16620 - - -
6 VANE PUMP ASSEMBLY 44310 - - -
7 ENGINE WATER PUMP ASSEMBLY 16100 - - -

*A for Separate Type *B for Integrated Type
*1 IDLER PULLEY COVER PLATE *2 NO. 2 IDLER PULLEY COVER PLATE
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine water pump assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Parking assist monitor system (Click here)
Front bumper assembly (Including removal and installation) Front television camera view adjustment Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 1.REMOVE COMPRESSOR WITH MAGNET CLUTCH

Hide 17360G 2.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

Hide 3.REMOVE WATER INLET ASSEMBLY

a.
A488708C01
0,0 0,0 false


Hide 16604 4.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.
A488712C01
1.646,0.094 2.104,0.375 0.458,0.281 18 false i, ii

i.

for Separate Type:

1. Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulley sub-assemblies and 2 No. 2 idler pulley cover plates.


ii.

for Integrated Type:

1. Remove the 2 bolts and 2 No. 2 idler pulley sub-assemblies.



Hide 16620 5.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 44310 6.DISCONNECT VANE PUMP ASSEMBLY

a.
A488711


Hide 16100 7.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A488713