| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | ENGINE ASSEMBLY | - | - | - | - |
| 2 | NO. 1 EMISSION CONTROL VALVE SET | 25701B | - | - | - |
| 3 | NO. 2 EMISSION CONTROL VALVE SET | 25702B | - | - | - |
| *A | w/ Secondary Air Injection System | - | - |
| *A | for Separate Type | *B | for Integrated Type |
| *1 | ENGINE OIL LEVEL DIPSTICK | *2 | NO. 2 IDLER PULLEY COVER PLATE |
| *3 | IDLER PULLEY COVER PLATE | *4 | NO. 1 WATER BY-PASS HOSE |
| *5 | NO. 2 WATER BY-PASS HOSE | *6 | NO. 3 WATER BY-PASS HOSE |
| ● | Non-reusable part | - | - |
| *1 | OIL CONTROL VALVE FILTER LH | *2 | OIL CONTROL VALVE FILTER RH |
| *3 | SEAL WASHER | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the oil pump removal/installation are shown below.
1.REMOVE ENGINE ASSEMBLY
25701B 2.REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
25702B 3.REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
11452 5.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
6.REMOVE WATER INLET ASSEMBLY
16206 7.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
16603 8.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
16604 9.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
16620 10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
15671 11.REMOVE OIL FILTER BRACKET
13471 12.REMOVE CRANKSHAFT PULLEY
Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.
Using the pulley set bolt and SST, remove the crankshaft pulley and pulley set bolt.
15771 13.REMOVE NO. 1 OIL PIPE
Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.
Do not touch the mesh when removing the oil control valve filter LH.
15772 14.REMOVE NO. 2 OIL PIPE
Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.
Do not touch the mesh when removing the oil control valve filter RH.
15.DISCONNECT FUEL PIPE SUB-ASSEMBLY
11202 16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
11201 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
12102A 18.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 10 bolts and 2 nuts.
Make sure the removed parts are returned to the same places they were removed from.
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Be careful not to damage the contact surfaces of the oil pans.
15104 19.REMOVE OIL STRAINER SUB-ASSEMBLY
12101R 20.REMOVE NO. 1 OIL PAN SUB-ASSEMBLY
| *a | LH Side | *b | RH Side |
| *c | Pry | - | - |
Remove the 17 bolts and 2 nuts.
Make sure the removed parts are returned to the same places they were removed from.
Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly as shown in the illustration.
Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.
Tape the screwdriver tip before use.
Remove the 3 O-rings from the timing chain cover sub-assembly.
11302 21.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 26 bolts and 2 nuts.
Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.
Be careful not to damage the contact surfaces of the timing chain cover sub-assembly, cylinder block sub-assembly and cylinder head sub-assembly.
Tape the screwdriver tip before use.
Remove the oil pump gasket from the cylinder block sub-assembly.
11301C 22.REMOVE FRONT CRANKSHAFT OIL SEAL
Using a screwdriver and wooden block, pry out the front crankshaft oil seal.
Do not damage the surface of the oil seal press fit hole.
Tape the screwdriver tip before use.