Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469676 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C168E87  Side Camera (Left) Image Signal Missing Message  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly LH to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C168E87 Side Camera (Left) Image Signal Missing Message Side camera feedback malfunction (Left)
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH

·

Outer mirror retractor LH


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E461423E03
5.833,2.583 6.24,2.771 0.406,0.188 10 false I130 5.833,2.74 7.104,2.969 1.271,0.229 10 false Parking Assist ECU 0.75,3.177 3.052,3.385 2.302,0.208 10 false Outer Rear View Mirror Assembly LH 0.375,2.365 1.844,2.729 1.469,0.365 10 false Side Television Camera Assembly LH 0.75,3 1.094,3.188 0.344,0.188 10 false N18 5.958,2.052 6.438,2.25 0.479,0.198 10 false SGND 5.958,1.646 6.448,1.844 0.49,0.198 10 false LGND 5.979,1.219 6.417,1.417 0.438,0.198 10 false LCV- 5.979,0.792 6.417,1 0.438,0.208 10 false LCV+ 5.969,0.417 6.406,0.604 0.438,0.188 10 false LCB+ 3.552,0.323 3.958,0.531 0.406,0.208 10 false LCB+ 3.521,1.563 3.958,1.76 0.438,0.198 10 false LGND 4.938,2.01 5.094,2.208 0.156,0.198 10 false * 0.417,3.458 1.448,3.771 1.031,0.313 10 false *: Shielded 0.385,2.146 0.656,2.375 0.271,0.229 10 false A 1.979,1.125 2.146,1.313 0.167,0.188 10 false 2 1.979,0.323 2.146,0.521 0.167,0.198 10 false 3 1.969,0.719 2.167,0.906 0.198,0.188 10 false 4 1.979,1.948 2.156,2.135 0.177,0.188 10 false 5 1.458,2.01 1.938,2.229 0.479,0.219 10 false SGND 1.5,0.417 1.948,0.635 0.448,0.219 10 false LCB+ 3.552,0.708 4,0.885 0.448,0.177 10 false LCV+ 1.51,0.781 1.969,0.99 0.458,0.208 10 false LCV+ 3.573,1.094 3.958,1.292 0.385,0.198 10 false LCV- 1.521,1.188 1.948,1.396 0.427,0.208 10 false LCV- 1.469,1.646 1.958,1.833 0.49,0.188 10 false LGND 3.51,1.958 3.938,2.156 0.427,0.198 10 false SGND 1.979,1.563 2.146,1.74 0.167,0.177 10 false 1 4.052,0.313 4.365,0.51 0.313,0.198 10 false 2 5.802,0.333 5.99,0.51 0.188,0.177 10 false 2 4.052,0.719 4.365,0.917 0.313,0.198 10 false 4 5.781,0.708 5.969,0.906 0.188,0.198 10 false 4 4.052,1.115 4.365,1.313 0.313,0.198 10 false 3 5.76,1.115 5.958,1.313 0.198,0.198 10 false 3 4.063,1.531 4.375,1.729 0.313,0.198 10 false 1 5.781,1.583 6.094,1.781 0.313,0.198 10 false 1 4.021,1.969 4.333,2.167 0.313,0.198 10 false 5 5.781,1.938 6,2.125 0.219,0.188 10 false 5 2.219,2.354 3.792,2.552 1.573,0.198 10 false Outer Mirror Retractor LH

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the I130 parking assist ECU connector.


b.

Disconnect the N18 outer rear view mirror assembly LH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I130,N18)Location & Routing

Click Connector(I130)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(N18)Body>Front Door Wire LH>Television Camera Assembly Side LH

I130-2 (LCB+) - N18-2 (LCB+) Always Below 1 Ω
I130-4 (LCV+) - N18-4 (LCV+) Always Below 1 Ω
I130-3 (LCV-) - N18-3 (LCV-) Always Below 1 Ω
I130-1 (LGND) - N18-1 (LGND) Always Below 1 Ω
I130-5 (SGND) - N18-5 (SGND) Always Below 1 Ω
I130-2 (LCB+) or N18-2 (LCB+) - Body ground Always 10 kΩ or higher
I130-4 (LCV+) or N18-4 (LCV+) - Body ground Always 10 kΩ or higher
I130-3 (LCV-) or N18-3 (LCV-) - Body ground Always 10 kΩ or higher
I130-1 (LGND) or N18-1 (LGND) - Body ground Always 10 kΩ or higher
I130-5 (SGND) or N18-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

2.CHECK PARKING ASSIST ECU (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (LCV-, LGND)

Pre-procedure1

a.
E394297C01
1.969,0.885 2.333,0.5 2.333,0.5 2.583,0.5 true 1.969,1.115 2.333,1.5 2.333,1.5 2.583,1.5 true 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 2.656,0.427 3.271,0.625 0.615,0.198 10 false LGND 2.646,1.438 3.26,1.635 0.615,0.198 10 false LCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the I130 parking assist ECU connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (LGND) - Body ground Always Below 1 Ω
3 (LCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

3.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

3.CHECK PARKING ASSIST ECU (LCB+, LGND)

Pre-procedure1

a.

Disconnect the N18 outer rear view mirror assembly LH connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N18)Location & Routing

Click Connector(N18)Body>Front Door Wire LH>Television Camera Assembly Side LH

N18-1 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(N18)Location & Routing

Click Connector(N18)Body>Front Door Wire LH>Television Camera Assembly Side LH

N18-2 (LCB+) - N18-1 (LGND) Ignition switch ON 7 to 8 V
N18-2 (LCB+) - N18-1 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


d.

None

Post-procedure1



OK

4.INSPECT OUTER MIRROR RETRACTOR LH

NG

4.INSPECT OUTER MIRROR RETRACTOR LH
a.
E461497C01
1.521,0.094 1.938,0.313 0.417,0.219 0.917,4.25 1,4.25 1,4.25 1.521,3.927 true 2.417,4.5 2.25,4.5 2.25,4.5 1.75,4.135 true 2.417,4.167 2.333,4.167 2.333,4.167 1.823,3.875 true 2.417,3.333 2.333,3.333 2.333,3.333 1.833,3.667 true 0.917,3.333 1,3.333 1,3.333 1.531,3.667 true 2.417,1.833 2.333,1.833 2.333,1.833 1.75,1.167 true 2.25,1.333 2.167,1.333 2.167,1.333 1.802,1.01 true 2.25,0.5 2.167,0.5 2.167,0.5 1.802,0.844 true 1.167,0.5 1.25,0.5 1.25,0.5 1.646,0.844 true 1.167,1.333 1.25,1.333 1.25,1.333 1.656,1 true 0.188,0.083 0.5,0.281 0.313,0.198 10 false *a 0.188,2.719 0.5,2.917 0.313,0.198 10 false *b 0.802,1.25 1.417,1.448 0.615,0.198 10 false LCB+ 2.302,0.417 2.917,0.615 0.615,0.198 10 false LCV- 2.302,1.25 2.917,1.448 0.615,0.198 10 false LCV+ 0.76,0.427 1.375,0.625 0.615,0.198 10 false LGND 2.469,1.75 3.083,1.948 0.615,0.198 10 false SGND 0.5,4.167 1.115,4.365 0.615,0.198 10 false LCV- 0.5,3.25 1.115,3.448 0.615,0.198 10 false LGND 2.5,3.25 3.115,3.448 0.615,0.198 10 false LCB+ 2.469,4.083 3.083,4.281 0.615,0.198 10 false LCV+ 2.5,4.417 3.115,4.615 0.615,0.198 10 false SGND 1.677,0.125 1.927,0.323 0.25,0.198 10 false A
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (LCB+) - A-3 (LCB+) Always Below 1 Ω
4 (LCV+) - A-4 (LCV+) Always Below 1 Ω
3 (LCV-) - A-2 (LCV-) Always Below 1 Ω
1 (LGND) - A-1 (LGND) Always Below 1 Ω
5 (SGND) - A-5 (SGND) Always Below 1 Ω
2 (LCB+) or A-3 (LCB+) - Body ground Always 10 kΩ or higher
4 (LCV+) or A-4 (LCV+) - Body ground Always 10 kΩ or higher
3 (LCV-) or A-2 (LCV-) - Body ground Always 10 kΩ or higher
1 (LGND) or A-1 (LGND) - Body ground Always 10 kΩ or higher
5 (SGND) or A-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER MIRROR RETRACTOR LH

5.REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 470

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 470

Result:
Result Proceed to
C168E87 is not output A
C168E87 is output B



A

END (SIDE TELEVISION CAMERA ASSEMBLY LH WAS DEFECTIVE)

B