Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469676 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C169E11  Side Camera (Right) Circuit Short to Ground  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly RH to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C169E11 Side Camera (Right) Circuit Short to Ground Side camera current malfunction (Right)
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly RH

·

Outer mirror retractor RH


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E461424E04
0.833,2.313 3.156,2.51 2.323,0.198 10 false Outer Rear View Mirror Assembly RH 0.823,2.104 1.094,2.302 0.271,0.198 10 false M19 0.427,1.323 0.615,1.51 0.188,0.188 10 false B 0.406,1.49 1.854,1.865 1.448,0.375 10 false Side Television Camera Assembly RH 2.198,0.396 2.333,0.542 0.135,0.146 10 false 3 2.198,0.875 2.333,1.021 0.135,0.146 10 false 1 1.688,0.448 2.177,0.604 0.49,0.156 10 false RCB+ 1.688,0.938 2.156,1.115 0.469,0.177 10 false RGND 3.781,0.406 4.219,0.615 0.438,0.208 10 false RCB+ 4.323,0.417 4.458,0.604 0.135,0.188 10 false 2 3.76,0.865 4.26,1.021 0.5,0.156 10 false RGND 4.313,0.854 4.479,1.031 0.167,0.177 10 false 1 5.833,1.75 7.104,1.979 1.271,0.229 10 false Parking Assist ECU 5.823,1.583 6.219,1.771 0.396,0.188 10 false I129 5.938,0.5 6.375,0.677 0.438,0.177 10 false RCB+ 5.948,0.979 6.385,1.135 0.438,0.156 10 false RGND 5.74,0.427 5.927,0.594 0.188,0.167 10 false 2 5.75,0.917 5.938,1.083 0.188,0.167 10 false 1 2.417,1.333 4.021,1.563 1.604,0.229 10 false Outer Mirror Retractor RH

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the I129 parking assist ECU connector.


b.

Disconnect the M19 outer rear view mirror assembly RH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I129,M19)Location & Routing

Click Connector(I129)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(M19)Body>Front Door Wire RH>Television Camera Assembly Side RH

I129-2 (RCB+) - M19-2 (RCB+) Always Below 1 Ω
I129-1 (RGND) - M19-1 (RGND) Always Below 1 Ω
I129-2 (RCB+) or M19-2 (RCB+) - Body ground Always 10 kΩ or higher
I129-1 (RGND) or M19-1 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

2.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU

Pre-procedure1

a.

Disconnect the M19 outer rear view mirror assembly LH connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M19)Location & Routing

Click Connector(M19)Body>Front Door Wire RH>Television Camera Assembly Side RH

M19-1 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(M19)Location & Routing

Click Connector(M19)Body>Front Door Wire RH>Television Camera Assembly Side RH

M19-2 (RCB+) - M19-1 (RGND) Ignition switch ON 7 to 8 V
M19-2 (RCB+) - M19-1 (RGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

3.INSPECT OUTER MIRROR RETRACTOR RH

NG

3.INSPECT OUTER MIRROR RETRACTOR RH

Pre-procedure1

a.
E461497C04
1.5,0.083 2,0.333 0.5,0.25 2.333,3.333 2.25,3.333 2.25,3.333 1.833,3.667 true 1,3.333 1.083,3.333 1.083,3.333 1.531,3.667 true 1.167,0.5 1.25,0.5 1.25,0.5 1.667,0.833 true 1.167,1.333 1.25,1.333 1.25,1.333 1.646,1 true 0.25,0.135 0.563,0.333 0.313,0.198 10 false *a 0.188,2.75 0.5,2.948 0.313,0.198 10 false *b 0.719,1.25 1.333,1.448 0.615,0.198 10 false RCB+ 0.75,0.417 1.365,0.615 0.615,0.198 10 false RGND 0.552,3.25 1.167,3.448 0.615,0.198 10 false RGND 2.385,3.25 3,3.448 0.615,0.198 10 false RCB+ 1.698,0.125 1.948,0.323 0.25,0.198 10 false B
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RCB+) - B-3 (RCB+) Always Below 1 Ω
1 (RGND) - B-1 (RGND) Always Below 1 Ω
2 (RCB+) or B-3 (RCB+) - Body ground Always 10 kΩ or higher
1 (RGND) or B-1 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

4.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER MIRROR RETRACTOR RH

4.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 470

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 470

Result:
Result Proceed to
C169E11 is not output A
C169E11 is output B



A

END (SIDE TELEVISION CAMERA ASSEMBLY RH WAS DEFECTIVE)

B