Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469676 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  Image from Camera for Panoramic View Monitor is Abnormal  


DESCRIPTION

The display signal from each television camera is transmitted to the multi-display assembly via the parking assist ECU.

WIRING DIAGRAM

E431824E07
1.365,7.208 1.844,7.406 0.479,0.198 10 false CGND 1.375,7.688 1.875,7.885 0.5,0.198 10 false SGND 1.375,4.698 1.99,4.896 0.615,0.198 10 false SGND 0.635,5.125 2.906,5.406 2.271,0.281 10 false Front Television Camera Assembly 5.417,8.188 6.656,8.396 1.24,0.208 10 false Parking Assist ECU 2.01,0.115 2.313,0.344 0.302,0.229 10 false 1 2.021,0.615 2.25,0.813 0.229,0.198 10 false 2 2.01,1.135 2.167,1.333 0.156,0.198 10 false 3 0.635,7.969 0.927,8.146 0.292,0.177 10 false g18 1.51,6.708 1.813,6.896 0.302,0.188 10 false CV- 1.49,6.229 1.844,6.406 0.354,0.177 10 false CV+ 1.469,5.719 1.833,5.917 0.365,0.198 10 false CB+ 5.531,5.729 5.865,5.917 0.333,0.188 10 false CB+ 5.521,6.24 5.854,6.438 0.333,0.198 10 false CV+ 5.521,6.74 5.833,6.958 0.313,0.219 10 false CV- 5.531,7.219 6,7.406 0.469,0.188 10 false CGND 1.896,3.125 2.271,3.302 0.375,0.177 10 false 4 1.896,2.635 2.271,2.813 0.375,0.177 10 false 2 1.896,3.646 2.271,3.823 0.375,0.177 10 false 3 0.646,4.969 0.938,5.156 0.292,0.188 10 false A11 1.344,4.219 1.958,4.417 0.615,0.198 10 false BGND 1.375,3.708 1.99,3.906 0.615,0.198 10 false BCV- 1.365,3.219 1.979,3.417 0.615,0.198 10 false BCV+ 1.365,2.729 1.979,2.927 0.615,0.198 10 false BCB+ 1.896,4.625 2.219,4.802 0.323,0.177 10 false 5 1.896,4.146 2.219,4.323 0.323,0.177 10 false 1 5.177,2.51 5.563,2.677 0.385,0.167 10 false 2 5.188,3 5.521,3.177 0.333,0.177 10 false 4 3.385,7.76 3.542,7.958 0.156,0.198 10 false * 5.177,0.115 5.563,0.333 0.385,0.219 10 false 1 5.198,0.604 5.406,0.771 0.208,0.167 10 false 2 5.188,1.104 5.365,1.302 0.177,0.198 10 false 3 5.521,1.854 6.01,2.052 0.49,0.198 10 false RSW+ 1.385,0.333 1.833,0.521 0.448,0.188 10 false GVO+ 1.385,0.802 1.781,0.979 0.396,0.177 10 false GVO- 1.375,1.313 1.813,1.51 0.438,0.198 10 false GVG1 1.906,6.156 2.073,6.344 0.167,0.188 10 false 6 1.896,5.667 2.052,5.833 0.156,0.167 10 false 4 1.917,7.135 2.094,7.313 0.177,0.177 10 false 3 1.906,7.615 2.083,7.823 0.177,0.208 10 false 7 1.917,6.656 2.042,6.823 0.125,0.167 10 false 5 0.635,8.115 2.781,8.333 2.146,0.219 10 false Rear Television Camera Assembly 5.521,0.333 5.99,0.531 0.469,0.198 10 false GVO+ 5.521,0.823 5.958,1.01 0.438,0.188 10 false GVO- 5.531,1.323 5.979,1.51 0.448,0.188 10 false GVG1 5.073,1.333 5.49,1.521 0.417,0.188 10 false I124 5.531,2.719 5.969,2.917 0.438,0.198 10 false BCB+ 5.521,3.208 5.958,3.406 0.438,0.198 10 false BCV+ 5.531,3.719 5.938,3.917 0.406,0.198 10 false BCV- 5.531,4.219 6.021,4.417 0.49,0.198 10 false BGND 5.177,3.51 5.51,3.688 0.333,0.177 10 false 3 5.188,4.01 5.521,4.188 0.333,0.177 10 false 1 5.188,4.5 5.521,4.677 0.333,0.177 10 false 5 5.073,4.708 5.49,4.896 0.417,0.188 10 false I128 3.375,4.781 3.531,4.979 0.156,0.198 10 false * 3.385,1.313 3.542,1.51 0.156,0.198 10 false * 5.094,7.698 5.51,7.885 0.417,0.188 10 false I131 5.177,5.51 5.604,5.688 0.427,0.177 10 false 2 5.198,6.031 5.573,6.208 0.375,0.177 10 false 4 5.198,6.521 5.573,6.698 0.375,0.177 10 false 3 5.188,7.01 5.51,7.188 0.323,0.177 10 false 1 5.198,7.5 5.521,7.677 0.323,0.177 10 false 5 5.521,7.698 5.979,7.885 0.458,0.188 10 false SGND 0.76,8.479 1.615,8.667 0.854,0.188 10 false : GVIF Cable 2.26,8.5 3.177,8.688 0.917,0.188 10 false *: Shielded 5.521,4.708 5.99,4.906 0.469,0.198 10 false SGND 0.521,2.146 2.792,2.427 2.271,0.281 10 false Multi-display Assembly 1.354,1.833 1.823,2.021 0.469,0.188 10 false CSW+ 5.135,1.854 5.448,2.031 0.313,0.177 10 false I60 5.156,1.615 5.396,1.781 0.24,0.167 10 false 13 2.01,1.635 2.313,1.865 0.302,0.229 10 false 1 1.917,1.844 2.229,2.01 0.313,0.167 10 false I18 1.885,1.323 2.25,1.5 0.365,0.177 10 false I125 1.917,0.823 2.281,1 0.365,0.177 10 false I125 1.906,0.354 2.271,0.531 0.365,0.177 10 false I125 5.083,0.844 5.5,1.031 0.417,0.188 10 false I124 5.073,0.344 5.49,0.531 0.417,0.188 10 false I124 5.083,7.229 5.5,7.417 0.417,0.188 10 false I131 5.094,6.76 5.51,6.948 0.417,0.188 10 false I131 5.073,6.24 5.49,6.427 0.417,0.188 10 false I131 5.094,5.74 5.51,5.927 0.417,0.188 10 false I131 5.104,4.229 5.521,4.417 0.417,0.188 10 false I128 5.083,3.719 5.5,3.906 0.417,0.188 10 false I128 5.094,3.229 5.51,3.417 0.417,0.188 10 false I128 5.083,2.74 5.5,2.927 0.417,0.188 10 false I128

E461425E02
5.073,2.635 5.458,2.844 0.385,0.208 10 false I130 5.094,6.958 5.458,7.125 0.365,0.167 10 false I129 5.198,0.396 5.354,0.573 0.156,0.177 10 false 2 5.188,0.896 5.354,1.083 0.167,0.188 10 false 4 5.188,1.396 5.333,1.583 0.146,0.188 10 false 3 5.188,1.885 5.448,2.073 0.26,0.188 10 false 1 5.198,2.417 5.458,2.604 0.26,0.188 10 false 5 3.76,0.49 4.021,0.677 0.26,0.188 10 false 2 3.75,1.01 4.01,1.198 0.26,0.188 10 false 4 3.76,1.51 4.021,1.698 0.26,0.188 10 false 3 3.771,2.021 4.031,2.208 0.26,0.188 10 false 1 3.771,2.51 4.031,2.698 0.26,0.188 10 false 5 1.906,1.521 2.167,1.708 0.26,0.188 10 false 2 1.896,2.031 2.156,2.219 0.26,0.188 10 false 1 1.917,0.49 2.177,0.677 0.26,0.188 10 false 3 1.906,1.021 2.167,1.208 0.26,0.188 10 false 4 1.917,2.521 2.177,2.708 0.26,0.188 10 false 5 1.396,0.573 1.823,0.792 0.427,0.219 10 false LCB+ 1.427,1.583 1.813,1.781 0.385,0.198 10 false LCV- 1.396,1.104 1.823,1.313 0.427,0.208 10 false LCV+ 1.375,2.104 1.844,2.313 0.469,0.208 10 false LGND 1.375,2.625 1.854,2.823 0.479,0.198 10 false SGND 5.521,0.594 5.917,0.771 0.396,0.177 10 false LCB+ 5.531,1.094 5.938,1.313 0.406,0.219 10 false LCV+ 5.542,1.594 5.948,1.792 0.406,0.198 10 false LCV- 5.542,2.104 5.99,2.313 0.448,0.208 10 false LGND 5.542,2.615 6.01,2.802 0.469,0.188 10 false SGND 3.24,0.5 3.646,0.698 0.406,0.198 10 false LCB+ 3.25,1.01 3.667,1.219 0.417,0.208 10 false LCV+ 3.26,1.51 3.656,1.719 0.396,0.208 10 false LCV- 3.177,2.01 3.635,2.198 0.458,0.188 10 false LGND 3.188,2.531 3.635,2.74 0.448,0.208 10 false SGND 0.313,2.781 0.49,2.979 0.177,0.198 10 false A 0.302,2.979 1.76,3.313 1.458,0.333 10 false Side Television Camera Assembly LH 0.677,8.052 1.01,8.229 0.333,0.177 10 false M19 0.542,3.906 2.865,4.135 2.323,0.229 10 false Outer Rear View Mirror Assembly LH 0.677,8.24 3.01,8.427 2.333,0.188 10 false Outer Rear View Mirror Assembly RH 0.323,7.115 0.531,7.302 0.208,0.188 10 false B 0.313,7.281 1.771,7.677 1.458,0.396 10 false Side Television Camera Assembly RH 0.531,3.729 0.865,3.906 0.333,0.177 10 false N18 3.771,6.833 3.938,7.021 0.167,0.188 10 false 5 3.76,6.333 3.948,6.5 0.188,0.167 10 false 1 3.771,5.833 3.958,6 0.188,0.167 10 false 3 3.771,5.333 3.938,5.521 0.167,0.188 10 false 4 3.76,4.823 3.927,5.01 0.167,0.188 10 false 2 5.198,4.667 5.385,4.854 0.188,0.188 10 false 2 5.188,5.188 5.354,5.375 0.167,0.188 10 false 4 5.177,5.698 5.333,5.885 0.156,0.188 10 false 3 5.177,6.198 5.333,6.406 0.156,0.208 10 false 1 5.208,6.74 5.385,6.927 0.177,0.188 10 false 5 1.906,5.844 2.167,6.031 0.26,0.188 10 false 2 1.906,6.333 2.073,6.51 0.167,0.177 10 false 1 1.906,4.802 2.083,4.99 0.177,0.188 10 false 3 1.917,5.323 2.177,5.51 0.26,0.188 10 false 4 1.906,6.865 2.073,7.052 0.167,0.188 10 false 5 1.375,4.875 1.813,5.063 0.438,0.188 10 false RCB+ 1.406,5.406 1.854,5.615 0.448,0.208 10 false RCV+ 1.438,5.906 1.844,6.125 0.406,0.219 10 false RCV- 1.375,6.438 1.823,6.635 0.448,0.198 10 false RGND 1.385,6.938 1.823,7.146 0.438,0.208 10 false SGND 3.219,4.823 3.646,5.01 0.427,0.188 10 false RCB+ 3.219,5.323 3.646,5.51 0.427,0.188 10 false RCV+ 3.271,5.833 3.688,6.042 0.417,0.208 10 false RCV- 3.208,6.344 3.677,6.552 0.469,0.208 10 false RGND 3.177,6.844 3.625,7.042 0.448,0.198 10 false SGND 5.521,4.885 5.958,5.083 0.438,0.198 10 false RCB+ 5.521,5.406 5.958,5.594 0.438,0.188 10 false RCV+ 5.542,5.917 5.927,6.104 0.385,0.188 10 false RCV- 5.542,6.438 6.031,6.615 0.49,0.177 10 false RGND 5.521,6.938 5.958,7.125 0.438,0.188 10 false SGND 0.219,8.438 2.688,8.677 2.469,0.24 10 false *: Shielded 5.427,7.531 6.729,7.74 1.302,0.208 10 false Parking Assist ECU 4.313,2.615 4.448,2.771 0.135,0.156 10 false * 4.313,6.917 4.479,7.094 0.167,0.177 10 false * 1.969,2.99 3.583,3.167 1.615,0.177 10 false Outer Mirror Retractor LH 1.969,7.292 3.594,7.49 1.625,0.198 10 false Outer Mirror Retractor RH 5.104,6.469 5.469,6.635 0.365,0.167 10 false I129 5.073,5.938 5.438,6.104 0.365,0.167 10 false I129 5.115,5.438 5.479,5.604 0.365,0.167 10 false I129 5.104,4.917 5.469,5.083 0.365,0.167 10 false I129 5.094,0.625 5.479,0.833 0.385,0.208 10 false I130 5.094,1.125 5.479,1.333 0.385,0.208 10 false I130 5.115,1.615 5.5,1.823 0.385,0.208 10 false I130 5.094,2.125 5.479,2.333 0.385,0.208 10 false I130

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



HINT:
Images may be unclear even in normal conditions if:
·

Electrical devices are used in the cabin (noise may occur in the image).

·

The camera lens is frosted over (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night, etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The television camera assembly lens is scratched.

·

The television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK PANORAMIC VIEW MONITOR SYSTEM
a.

Check if the same malfunction occurs when the panoramic view monitor screen is displayed.


Result:
Result Proceed to
Rear view screen is not displayed. A
Front view screen is not displayed. B
Side monitor screen (LH side) is not displayed. C
Side monitor screen (RH side) is not displayed. D
Panoramic view monitor screen is not displayed. E



A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)

D

13.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)

E

18.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - MULTI- DISPLAY ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the I131 parking assist ECU connector.


b.

Disconnect the g18 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I131,g18)Location & Routing

Click Connector(I131)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

I131-2 (CB+) - g18-4 (CB+) Always Below 1 Ω
I131-4 (CV+) - g18-6 (CV+) Always Below 1 Ω
I131-3 (CV-) - g18-5 (CV-) Always Below 1 Ω
I131-1 (CGND) - g18-3 (CGND) Always Below 1 Ω
I131-5 (SGND) - g18-7 (SGND) Always Below 1 Ω
I131-2 (CB+) or g18-4 (CB+) - Body ground Always 10 kΩ or higher
I131-4 (CV+) or g18-6 (CV+) - Body ground Always 10 kΩ or higher
I131-3 (CV-) or g18-5 (CV-) - Body ground Always 10 kΩ or higher
I131-1 (CGND) or g18-3 (CGND) - Body ground Always 10 kΩ or higher
I131-5 (SGND) - g18-7 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (CV-, CGND)
a.
E394295C01
1.979,0.854 2.333,0.479 2.333,0.479 2.583,0.479 true 2,1.104 2.354,1.563 2.354,1.563 2.604,1.563 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.646,0.417 3.167,0.615 0.521,0.198 10 false CGND 2.667,1.49 3.188,1.688 0.521,0.198 10 false CV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the I131 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (CGND) - Body ground Always Below 1 Ω
3 (CV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

4.CHECK PARKING ASSIST ECU (CB+, CGND)
a.

Disconnect the g18 rear television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(g18)Location & Routing

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g18-3 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(g18)Location & Routing

Click Connector(g18)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

g18-4 (CB+) - g18-3 (CGND) Ignition switch ON 7 to 8 V
g18-4 (CB+) - g18-3 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the I128 parking assist ECU connector.


b.

Disconnect the A11 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I128,A11)Location & Routing

Click Connector(I128)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(A11)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Front Television Camera Assembly

I128-2 (BCB+) - A11-2 (BCB+) Always Below 1 Ω
I128-4 (BCV+) - A11-4 (BCV+) Always Below 1 Ω
I128-3 (BCV-) - A11-3 (BCV-) Always Below 1 Ω
I128-1 (BGND) - A11-1 (BGND) Always Below 1 Ω
I128-5 (SGND) - A11-5 (SGND) Always Below 1 Ω
I128-2 (BCB+) or A11-2 (BCB+) - Body ground Always 10 kΩ or higher
I128-4 (BCV+) or A11-4 (BCV+) - Body ground Always 10 kΩ or higher
I128-3 (BCV-) or A11-3 (BCV-) - Body ground Always 10 kΩ or higher
I128-1 (BGND) or A11-1 (BGND) - Body ground Always 10 kΩ or higher
I128-5 (SGND) or A11-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK PARKING ASSIST ECU (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK PARKING ASSIST ECU (BCV-, BGND)
a.
E394296C01
1.969,0.854 2.313,0.417 2.313,0.417 2.563,0.417 true 1.979,1.083 2.313,1.552 2.313,1.552 2.563,1.552 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 2.615,0.344 3.229,0.542 0.615,0.198 10 false BGND 2.625,1.479 3.24,1.677 0.615,0.198 10 false BCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the I128 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (BGND) - Body ground Always Below 1 Ω
3 (BCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

7.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.

Disconnect the A11 front television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A11)Location & Routing

Click Connector(A11)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Front Television Camera Assembly

A11-1 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A11)Location & Routing

Click Connector(A11)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Front Television Camera Assembly

A11-2 (BCB+) - A11-1 (BGND) Ignition switch ON 7 to 8 V
A11-2 (BCB+) - A11-1 (BGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the I130 parking assist ECU connector.


b.

Disconnect the N18 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I130,N18)Location & Routing

Click Connector(I130)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(N18)Body>Front Door Wire LH>Television Camera Assembly Side LH

I130-2 (LCB+) - N18-2 (LCB+) Always Below 1 Ω
I130-4 (LCV+) - N18-4 (LCV+) Always Below 1 Ω
I130-3 (LCV-) - N18-3 (LCV-) Always Below 1 Ω
I130-1 (LGND) - N18-1 (LGND) Always Below 1 Ω
I130-5 (SGND) - N18-5 (SGND) Always Below 1 Ω
I130-2 (LCB+) or N18-2 (LCB+) - Body ground Always 10 kΩ or higher
I130-4 (LCV+) or N18-4 (LCV+) - Body ground Always 10 kΩ or higher
I130-3 (LCV-) or N18-3 (LCV-) - Body ground Always 10 kΩ or higher
I130-1 (LGND) or N18-1 (LGND) - Body ground Always 10 kΩ or higher
I130-5 (SGND) or N18-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK PARKING ASSIST ECU (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK PARKING ASSIST ECU (LCV-, LGND)
a.
E394297C01
1.969,0.885 2.333,0.5 2.333,0.5 2.583,0.5 true 1.969,1.115 2.333,1.5 2.333,1.5 2.583,1.5 true 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 2.656,0.427 3.271,0.625 0.615,0.198 10 false LGND 2.646,1.438 3.26,1.635 0.615,0.198 10 false LCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the I130 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (LGND) - Body ground Always Below 1 Ω
3 (LCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

10.CHECK PARKING ASSIST ECU (LCB+, LGND)
a.

Disconnect the N18 outer rear view mirror assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N18)Location & Routing

Click Connector(N18)Body>Front Door Wire LH>Television Camera Assembly Side LH

N18-1 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(N18)Location & Routing

Click Connector(N18)Body>Front Door Wire LH>Television Camera Assembly Side LH

N18-2 (LCB+) - N18-1 (LGND) Ignition switch ON 7 to 8 V
N18-2 (LCB+) - N18-1 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

11.INSPECT OUTER MIRROR RETRACTOR LH

NG

11.INSPECT OUTER MIRROR RETRACTOR LH
a.
E461497C01
1.521,0.094 1.938,0.313 0.417,0.219 0.917,4.25 1,4.25 1,4.25 1.521,3.927 true 2.417,4.5 2.25,4.5 2.25,4.5 1.75,4.135 true 2.417,4.167 2.333,4.167 2.333,4.167 1.823,3.875 true 2.417,3.333 2.333,3.333 2.333,3.333 1.833,3.667 true 0.917,3.333 1,3.333 1,3.333 1.531,3.667 true 2.417,1.833 2.333,1.833 2.333,1.833 1.75,1.167 true 2.25,1.333 2.167,1.333 2.167,1.333 1.802,1.01 true 2.25,0.5 2.167,0.5 2.167,0.5 1.802,0.844 true 1.167,0.5 1.25,0.5 1.25,0.5 1.646,0.844 true 1.167,1.333 1.25,1.333 1.25,1.333 1.656,1 true 0.188,0.083 0.5,0.281 0.313,0.198 10 false *a 0.188,2.719 0.5,2.917 0.313,0.198 10 false *b 0.802,1.25 1.417,1.448 0.615,0.198 10 false LCB+ 2.302,0.417 2.917,0.615 0.615,0.198 10 false LCV- 2.302,1.25 2.917,1.448 0.615,0.198 10 false LCV+ 0.76,0.427 1.375,0.625 0.615,0.198 10 false LGND 2.469,1.75 3.083,1.948 0.615,0.198 10 false SGND 0.5,4.167 1.115,4.365 0.615,0.198 10 false LCV- 0.5,3.25 1.115,3.448 0.615,0.198 10 false LGND 2.5,3.25 3.115,3.448 0.615,0.198 10 false LCB+ 2.469,4.083 3.083,4.281 0.615,0.198 10 false LCV+ 2.5,4.417 3.115,4.615 0.615,0.198 10 false SGND 1.677,0.125 1.927,0.323 0.25,0.198 10 false A
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (LCB+) - A-3 (LCB+) Always Below 1 Ω
4 (LCV+) - A-4 (LCV+) Always Below 1 Ω
3 (LCV-) - A-2 (LCV-) Always Below 1 Ω
1 (LGND) - A-1 (LGND) Always Below 1 Ω
5 (SGND) - A-5 (SGND) Always Below 1 Ω
2 (LCB+) or A-3 (LCB+) - Body ground Always 10 kΩ or higher
4 (LCV+) or A-4 (LCV+) - Body ground Always 10 kΩ or higher
3 (LCV-) or A-2 (LCV-) - Body ground Always 10 kΩ or higher
1 (LGND) or A-1 (LGND) - Body ground Always 10 kΩ or higher
5 (SGND) or A-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER MIRROR RETRACTOR LH

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH WAS DEFECTIVE)

NG

13.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the I129 parking assist ECU connector.


b.

Disconnect the M19 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I129,M19)Location & Routing

Click Connector(I129)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(M19)Body>Front Door Wire RH>Television Camera Assembly Side RH

I129-2 (RCB+) - M19-2 (RCB+) Always Below 1 Ω
I129-4 (RCV+) - M19-4 (RCV+) Always Below 1 Ω
I129-3 (RCV-) - M19-3 (RCV-) Always Below 1 Ω
I129-1 (RGND) - M19-1 (RGND) Always Below 1 Ω
I129-5 (SGND) - M19-5 (SGND) Always Below 1 Ω
I129-2 (RCB+) or M19-2 (RCB+) - Body ground Always 10 kΩ or higher
I129-4 (RCV+) or M19-4 (RCV+) - Body ground Always 10 kΩ or higher
I129-3 (RCV-) or M19-3 (RCV-) - Body ground Always 10 kΩ or higher
I129-1 (RGND) or M19-1 (RGND) - Body ground Always 10 kΩ or higher
I129-5 (SGND) or M19-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK PARKING ASSIST ECU (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK PARKING ASSIST ECU (RCV-, RGND)
a.
E394298C01
1.969,0.865 2.333,0.51 2.333,0.51 2.583,0.51 true 1.979,1.083 2.333,1.333 2.333,1.333 2.583,1.333 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 2.635,0.448 3.083,0.646 0.448,0.198 10 false RGND 2.635,1.26 3.083,1.458 0.448,0.198 10 false RCV-
*a Component without harness connected
(Parking Assist ECU)


Disconnect the I129 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (RGND) - Body ground Always Below 1 Ω
3 (RCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

15.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.

Disconnect the M19 outer rear view mirror assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M19)Location & Routing

Click Connector(M19)Body>Front Door Wire RH>Television Camera Assembly Side RH

M19-1 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(M19)Location & Routing

Click Connector(M19)Body>Front Door Wire RH>Television Camera Assembly Side RH

M19-2 (RCB+) - M19-1 (RGND) Ignition switch ON 7 to 8 V
M19-2 (RCB+) - M19-1 (RGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

16.INSPECT OUTER MIRROR RETRACTOR RH

NG

16.INSPECT OUTER MIRROR RETRACTOR RH
a.
E461497C02
1.5,0.083 2,0.333 0.5,0.25 1,4.167 1.083,4.167 1.083,4.167 1.583,3.917 true 2.333,4.417 2.25,4.417 2.25,4.417 1.729,4.135 true 2.333,4.167 2.25,4.167 2.25,4.167 1.823,3.917 true 2.333,3.333 2.25,3.333 2.25,3.333 1.833,3.667 true 1,3.333 1.083,3.333 1.083,3.333 1.531,3.667 true 2.323,1.75 2.24,1.75 2.24,1.75 1.75,1.167 true 2.25,1.333 2.167,1.333 2.167,1.333 1.813,1 true 2.25,0.5 2.167,0.5 2.167,0.5 1.771,0.833 true 1.167,0.5 1.25,0.5 1.25,0.5 1.667,0.833 true 1.167,1.333 1.25,1.333 1.25,1.333 1.646,1 true 0.25,0.135 0.563,0.333 0.313,0.198 10 false *a 0.188,2.75 0.5,2.948 0.313,0.198 10 false *b 0.719,1.25 1.333,1.448 0.615,0.198 10 false RCB+ 2.333,0.417 2.948,0.615 0.615,0.198 10 false RCV- 2.333,1.25 2.948,1.448 0.615,0.198 10 false RCV+ 0.75,0.417 1.365,0.615 0.615,0.198 10 false RGND 2.385,1.667 3,1.865 0.615,0.198 10 false SGND 0.583,4.083 1.198,4.281 0.615,0.198 10 false RCV- 0.552,3.25 1.167,3.448 0.615,0.198 10 false RGND 2.385,3.25 3,3.448 0.615,0.198 10 false RCB+ 2.385,4.083 3,4.281 0.615,0.198 10 false RCV+ 2.385,4.333 3,4.531 0.615,0.198 10 false SGND 1.698,0.125 1.948,0.323 0.25,0.198 10 false B
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RCB+) - B-3 (RCB+) Always Below 1 Ω
4 (RCV+) - B-4 (RCV+) Always Below 1 Ω
3 (RCV-) - B-2 (RCV-) Always Below 1 Ω
1 (RGND) - B-1 (RGND) Always Below 1 Ω
5 (SGND) or B-5 (SGND) Always 10 kΩ or higher
2 (RCB+) or B-3 (RCB+) - Body ground Always 10 kΩ or higher
4 (RCV+) or B-4 (RCV+) - Body ground Always 10 kΩ or higher
3 (RCV-) or B-2 (RCV-) - Body ground Always 10 kΩ or higher
1 (RGND) or B-1 (RGND) - Body ground Always 10 kΩ or higher
5 (SGND) or B-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER MIRROR RETRACTOR RH

17.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH WAS DEFECTIVE)

NG

18.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - MULTI- DISPLAY ASSEMBLY)
a.

Disconnect the I60 parking assist ECU connector.


b.

Disconnect the I18 multi-display assembly connector.



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (GVIF CABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.

Replace the GVIF cable with a new or normally functioning one.


b.

Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (GVIF CABLE WAS DEFECTIVE)

NG

20.CHECK MULTI-DISPLAY ASSEMBLY
20.CHECK MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL


b.

Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (MULTI-DISPLAY ASSEMBLY WAS DEFECTIVE)

NG