Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C102000  Ignition Switch On/Start Position Malfunction  


DESCRIPTION

Refer to DTC C110E14.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C110E14

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C102000 Ignition Switch On/Start Position Malfunction When the IG1 terminal voltage is less than 2.8 V, the IG2 terminal voltage is 10.2 V or more for 4 seconds or more.
·

Open or short in IG1 circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Backup boost converter circuit*

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

*: w/ Stop and Start System


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-31 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-31 (IG1) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)