Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL SENDER GAUGE ASSEMBLY (for Single Tank Type)
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0474718 FUEL SENDER GAUGE ASSEMBLY(for Single Tank Type) A

V35A-FTS FUEL  FUEL SENDER GAUGE ASSEMBLY(for Single Tank Type)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A487497N01
2.75,0.99 3.469,0.99 false 4.385,0.792 5.104,0.792 false 6.427,0.24 6.844,0.24 false 6.448,0.625 6.802,0.625 false 2.563,0.833 2.781,1.094 0.219,0.26 18 false 4 5.146,0.635 5.385,0.896 0.24,0.26 18 false 5 5.958,0.073 6.458,0.354 0.5,0.281 18 false 1, 2 6.271,0.479 6.51,0.74 0.24,0.26 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
4 FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY 77020A - - -
5 FUEL SENDER GAUGE ASSEMBLY 83320 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel sender gauge assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

Do not try to remove the black nylon tube as it is welded to the fuel suction with pump and gauge tube assembly.

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 77020A 4.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 83320 5.REMOVE FUEL SENDER GAUGE ASSEMBLY

a.
A487495