| *1 | NO. 4 REAR SIDE AIR DUCT | *2 | NO. 6 REAR SIDE AIR DUCT |
| *3 | REAR FLOOR SILENCER | *4 | FRONT FLOOR CARPET ASSEMBLY |
| *1 | BUTYL TAPE | *2 | TUBE JOINT CLIP |
| *3 | NO. 1 FUEL TUBE CLAMP | *4 | GASKET |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel suction with pump and gauge tube assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
77310A 4.REMOVE FUEL TANK CAP ASSEMBLY
5.REMOVE REAR NO. 1 SEAT ASSEMBLY
for LH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for LH Side)>REMOVAL
for 60/40 Split Seat Type RH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)>REMOVAL
for 40/20/40 Split Seat Type RH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 40/20/40 Split Seat Type RH Side)>REMOVAL
58410B 6.REMOVE DECK BOARD ASSEMBLY
58418H 8.REMOVE REAR FLOOR BOARD REAR LH
58417B 9.REMOVE REAR FLOOR BOARD REAR RH
Use the same procedure described for the LH side.
71695S 12.REMOVE REAR NO. 1 SEAT PROTECTOR
71695T 13.REMOVE REAR NO. 2 SEAT PROTECTOR
71695Y 14.REMOVE REAR NO. 3 SEAT PROTECTOR
Use the same procedure described for the rear No. 1 seat protector.
71F95 15.REMOVE REAR NO. 4 SEAT PROTECTOR
Use the same procedure described for the rear No. 1 seat protector.
67918D 16.REMOVE REAR DOOR SCUFF PLATE LH
67917C 17.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
58325E 18.REMOVE REAR FLOOR SERVICE HOLE COVER (for RH Side)
Detach the 6 clips and fold back the front floor carpet assembly.
Detach the 2 clips and remove the No. 4 rear side air duct and No. 6 rear side air duct.
Detach the 2 clips and fold back the rear floor silencer.
Remove the rear floor service hole cover and butyl tape.
77209C 19.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
| *1 | Tube Joint Clip | *2 | Fuel Suction Plate Sub-assembly |
| *a | Fuel Tube Joint | *b | O-Ring |
Remove the tube joint clip and disconnect the fuel tank main tube sub-assembly.
Remove any dirt and foreign matter on the fuel tube joint before performing this step.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tank main tube sub-assembly.
77144 20.REMOVE FUEL PUMP GAUGE RETAINER (for RH Side)
| *a | SST (Plate) | *b | SST (Bolt) |
| *c | SST (Claw) | *d | Insertion Point |
| *e | SST (Handle) | - | - |
Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
Install SST (handle) to SST (plate).
Check once more that the tip of SST is securely inserted into the insertion point of the fuel pump gauge retainer.
Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.
Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank sub-assembly.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
While pressing down on the fuel suction with pump and gauge tube assembly, remove the fuel pump gauge retainer.
77020A 21.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Remove the fuel suction with pump and gauge tube assembly from the fuel tank sub-assembly.
Be careful not to bend the arm of the fuel sender gauge assembly.
Remove the gasket from the fuel tank sub-assembly.