Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467496 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, for 12.3 Inch Display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, for 12.3 Inch Display)  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E462682E01
6.177,7.365 7.156,7.771 0.979,0.406 10 false Radio Receiver Assembly 0.208,7.271 1.104,7.854 0.896,0.583 10 false No. 6 Antenna Cord Sub-assembly 5.083,7.344 5.969,7.958 0.885,0.615 10 false Antenna Cord Sub-assembly 3.854,7.323 4.75,7.938 0.896,0.615 10 false No. 2 Antenna Cord Sub-assembly 0.021,3.188 1.25,3.594 1.229,0.406 10 false No. 5 Antenna Cord Sub-assembly 1.438,1.521 2.365,2.219 0.927,0.698 10 false No. 1 Amplifier Antenna Assembly 1.281,2.906 1.594,3.104 0.313,0.198 10 false F 5.979,0.719 6.292,0.917 0.313,0.198 10 false RA 5.99,1.156 6.302,1.354 0.313,0.198 10 false RA 5.979,1.583 6.292,1.781 0.313,0.198 10 false RA 5.979,2.021 6.292,2.219 0.313,0.198 10 false RA 1.271,0.271 1.583,0.469 0.313,0.198 10 false G 1.281,4.729 1.594,4.927 0.313,0.198 10 false A 1.281,6.917 1.594,7.115 0.313,0.198 10 false B 3.677,0.26 3.99,0.458 0.313,0.198 10 false I 3.677,0.719 3.99,0.917 0.313,0.198 10 false I 3.677,1.156 3.99,1.354 0.313,0.198 10 false I 4.833,0.26 5.146,0.458 0.313,0.198 10 false E 4.844,0.708 5.156,0.906 0.313,0.198 10 false E 4.844,1.146 5.156,1.344 0.313,0.198 10 false E 4.844,1.583 5.156,1.781 0.313,0.198 10 false E 4.844,2.021 5.156,2.219 0.313,0.198 10 false E 5.979,0.25 6.292,0.448 0.313,0.198 10 false RA 3.646,6.063 3.958,6.26 0.313,0.198 10 false D 3.646,6.49 3.958,6.688 0.313,0.198 10 false D 3.656,6.906 3.969,7.104 0.313,0.198 10 false D 6.031,0.073 6.344,0.271 0.313,0.198 10 false 3 6.031,0.531 6.344,0.729 0.313,0.198 10 false 4 6.042,0.958 6.354,1.156 0.313,0.198 10 false 1 6.042,1.396 6.354,1.594 0.313,0.198 10 false 2 6.052,1.813 6.365,2.01 0.313,0.198 10 false 5 6.26,2.031 6.781,2.302 0.521,0.271 10 false ANT+ 6.281,0.24 6.802,0.51 0.521,0.271 10 false MAIN 6.271,1.156 6.792,1.427 0.521,0.271 10 false SUB 4.844,0.083 5.156,0.281 0.313,0.198 10 false 5 4.802,0.51 5.115,0.708 0.313,0.198 10 false 5a 4.844,0.958 5.156,1.156 0.313,0.198 10 false 6 4.802,1.385 5.115,1.583 0.313,0.198 10 false 6a 4.854,1.833 5.177,2.042 0.323,0.208 10 false 4 3.656,0.073 3.969,0.271 0.313,0.198 10 false 3 3.615,0.51 3.927,0.708 0.313,0.198 10 false 3a 3.656,0.948 3.979,1.156 0.323,0.208 10 false 2 3.656,6.719 3.979,6.927 0.323,0.208 10 false 3 3.667,5.875 3.979,6.073 0.313,0.198 10 false 6 3.615,6.302 3.927,6.5 0.313,0.198 10 false 6a 1.281,6.729 1.594,6.927 0.313,0.198 10 false 1 1.281,4.531 1.594,4.729 0.313,0.198 10 false 1 1.292,0.083 1.604,0.281 0.313,0.198 10 false 2 1.281,2.719 1.604,2.927 0.323,0.208 10 false 1 1.5,7.271 2.417,7.906 0.917,0.635 10 false No. 2 Amplifier Antenna Assembly 2.656,7.313 3.552,7.927 0.896,0.615 10 false No. 3 Antenna Cord Sub-assembly 2.427,0.51 2.74,0.708 0.313,0.198 10 false 2a 2.469,0.083 2.792,0.292 0.323,0.208 10 false 2 2.458,0.958 2.781,1.167 0.323,0.208 10 false 1 2.458,0.26 2.781,0.469 0.323,0.208 10 false H 2.458,0.708 2.781,0.917 0.323,0.208 10 false H 2.448,1.146 2.771,1.354 0.323,0.208 10 false H 2.469,5.896 2.792,6.104 0.323,0.208 10 false 2 2.448,6.302 2.771,6.51 0.323,0.208 10 false 2a 2.469,6.719 2.781,6.917 0.313,0.198 10 false 1 2.458,6.073 2.771,6.271 0.313,0.198 10 false C 2.469,6.49 2.781,6.688 0.313,0.198 10 false C 2.458,6.906 2.771,7.104 0.313,0.198 10 false C 1.271,0.719 1.583,0.917 0.313,0.198 10 false G 1.271,6.49 1.583,6.688 0.313,0.198 10 false B 1.281,6.292 1.594,6.49 0.313,0.198 10 false 2 1.281,0.521 1.604,0.729 0.323,0.208 10 false 1 1.438,3.177 2.552,3.969 1.115,0.792 10 false Quarter Window Assembly LH (Window Glass Antenna Wire) 1.479,4.969 2.594,5.76 1.115,0.792 10 false Quarter Window Assembly RH (Window Glass Antenna Wire)

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a roof antenna, are installed.

OK:

Optional components are not installed.


NOTICE:

Do not remove optional components without the permission of the customer.



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO RECEIVER ASSEMBLY

NG

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO RECEIVER ASSEMBLY
a.
E245523

Preparation for check

i.

Disconnect the RA radio receiver assembly connector.



b.

Check for noise

i.

Turn the ignition switch to ON with the radio receiver assembly connector connected.


ii.

Turn the radio receiver assembly on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.




Result:
Proceed to
OK
NG



OK

4.CHECK QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)

NG

4.CHECK QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)
a.

Inspect the quarter window assembly (window glass antenna wire).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPAIR QUARTER WINDOW ASSEMBLY (WINDOW GLASS ANTENNA WIRE)

5.INSPECT RADIO RECEIVER ASSEMBLY
a.
E188455E31
1.552,1.104 1.146,1.479 true 0.844,1.51 1.24,1.677 0.396,0.167 10 ANT+

Disconnect the RA radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC, radio switch on and FM or AM selected 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E367065C01
1.531,0.146 1.875,0.396 0.344,0.25 1.563,1.865 1.906,2.115 0.344,0.25 1.01,0.667 1.49,0.896 true 1.01,1.552 1.49,1.302 true 1.677,0.896 2.167,0.365 2.167,0.365 2.323,0.365 true 1.917,1.104 2.229,1.104 true 1.646,1.292 2.115,1.667 2.115,1.667 2.292,1.667 true 2.688,3.156 2.552,2.833 true 2.073,3.177 2.177,2.833 true 1.604,0.188 1.854,0.354 0.25,0.167 10 false RA 1.688,1.906 1.833,2.083 0.146,0.177 10 false E 0.26,0.167 0.438,0.354 0.177,0.188 10 false *a 0.281,1.813 0.458,2 0.177,0.188 10 false *b 0.875,0.552 0.99,0.74 0.115,0.188 10 false 2 0.875,1.51 0.99,1.698 0.115,0.188 10 false 4 2.365,0.292 2.688,0.469 0.323,0.177 10 false SUB 2.292,1.021 2.688,1.188 0.396,0.167 10 false ANT+ 2.344,1.594 2.74,1.76 0.396,0.167 10 false MAIN 2.688,3.177 2.885,3.354 0.198,0.177 10 false 6a 1.979,3.177 2.177,3.354 0.198,0.177 10 false 5a
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the radio receiver assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - E-5 Always Below 1 Ω
RA-4 - E-5a Always Below 1 Ω
RA-1 (SUB) - E-6 Always Below 1 Ω
RA-2 - E-6a Always Below 1 Ω
RA-5 (ANT+) - E-4 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-1 (SUB) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E462692C01
0.052,0.729 0.479,0.969 0.427,0.24 0.094,2.333 0.521,2.573 0.427,0.24 0.458,3.771 0.885,4.01 0.427,0.24 2.906,3.198 2.698,3.198 2.698,3.198 2.594,2.677 true 1.781,1.771 1.573,1.771 1.573,1.771 1.448,1.104 true 0.708,1.781 0.875,1.781 0.875,1.781 1.083,1.104 true 1.292,4.479 1.458,4.479 1.458,4.479 1.594,4.177 true 1.375,2.281 1.688,2.479 0.313,0.198 10 false *a 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.073,1.635 0.385,1.833 0.313,0.198 10 false *b 0.219,0.771 0.531,0.969 0.313,0.198 10 false E 0.26,2.365 0.573,2.563 0.313,0.198 10 false D 0.667,3.802 0.979,4 0.313,0.198 10 false I 1.115,4.375 1.427,4.573 0.313,0.198 10 false 3a 2.948,3.104 3.26,3.302 0.313,0.198 10 false 6a 1.844,1.677 2.156,1.875 0.313,0.198 10 false 5a 0.542,1.688 0.854,1.885 0.313,0.198 10 false 6a
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-5 - I-3 Always Below 1 Ω
E-5a- I-3a Always Below 1 Ω
E-4 - I-2 Always Below 1 Ω
E-6 - D-6 Always Below 1 Ω
E-6a - D-6a Always Below 1 Ω
E-4 - D-3 Always Below 1 Ω
E-5 - Body ground Always 10 kΩ or higher
E-6 - Body ground Always 10 kΩ or higher
E-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

8.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E462691C01
0.417,0.417 0.75,0.667 0.333,0.25 0.469,1.604 0.802,1.854 0.333,0.25 0.167,2.75 0.5,3 0.333,0.25 1.729,2.698 2.063,2.948 0.333,0.25 0.948,1.094 1.125,1.094 1.125,1.094 1.271,0.76 true 2.385,2.292 2.219,2.292 2.219,2.292 1.927,1.979 true 1.563,3.281 1.396,3.281 1.396,3.281 1.208,2.969 true 2.896,3.25 2.729,3.25 2.729,3.25 2.573,2.969 true 0.063,0.094 0.375,0.292 0.313,0.198 10 false *a 0.083,2.292 0.396,2.49 0.313,0.198 10 false *b 0.51,0.469 0.823,0.667 0.313,0.198 10 false D 0.604,1.667 0.917,1.865 0.313,0.198 10 false I 0.896,2.625 1.208,2.823 0.313,0.198 10 false I 1.667,2.281 1.979,2.479 0.313,0.198 10 false *c 0.292,2.792 0.604,2.99 0.313,0.198 10 false H 1.865,2.75 2.177,2.948 0.313,0.198 10 false C 0.75,0.99 1.063,1.188 0.313,0.198 10 false 6a 2.427,2.198 2.74,2.396 0.313,0.198 10 false 3a 1.615,3.177 1.927,3.375 0.313,0.198 10 false 2a 2.948,3.156 3.26,3.354 0.313,0.198 10 false 2a
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*c Front view of wire harness connector
(to No. 2 Amplifier Antenna Assembly)


Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


c.

Disconnect the antenna connector from the No. 2 amplifier antenna assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I-3 - H-2 Always Below 1 Ω
I-3a - H-2a Always Below 1 Ω
I-2 - H-1 Always Below 1 Ω
D-6 - C-2 Always Below 1 Ω
D-6a - C-2a Always Below 1 Ω
D-3 - C-1 Always Below 1 Ω
I-3 - Body ground Always 10 kΩ or higher
I-3a - Body ground Always 10 kΩ or higher
I-2 - Body ground Always 10 kΩ or higher
D-6 - Body ground Always 10 kΩ or higher
D-6a - Body ground Always 10 kΩ or higher
D-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK NO. 5 ANTENNA CORD SUB-ASSEMBLY

NG

9.CHECK NO. 5 ANTENNA CORD SUB-ASSEMBLY
a.
E464135C01
1.51,0.219 1.844,0.521 0.333,0.302 1.51,2.667 1.844,2.969 0.333,0.302 0.26,0.167 0.573,0.365 0.313,0.198 10 false *a 0.302,2.49 0.615,2.688 0.313,0.198 10 false *b 1.635,2.719 1.948,2.917 0.313,0.198 10 false F 1.646,0.292 1.958,0.49 0.313,0.198 10 false G
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Quarter Window Assembly LH [Window Glass Antenna Wire])


Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


b.

Disconnect the antenna connector from the quarter window assembly LH (window glass antenna wire).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G-2 - F-1 Always Below 1 Ω
G-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK NO. 6 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 5 ANTENNA CORD SUB-ASSEMBLY

10.CHECK NO. 6 ANTENNA CORD SUB-ASSEMBLY
a.
E464135C02
1.51,0.219 1.844,0.521 0.333,0.302 1.51,2.677 1.844,2.979 0.333,0.302 0.26,0.167 0.573,0.365 0.313,0.198 10 false *a 0.281,2.448 0.594,2.646 0.313,0.198 10 false *b 1.625,2.74 1.938,2.948 0.313,0.208 10 false A 1.646,0.292 1.958,0.49 0.313,0.198 10 false B
*a Front view of wire harness connector
(to No. 2 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Quarter Window Assembly RH [window glass antenna wire])


Disconnect the antenna connector from the No. 2 amplifier antenna assembly.


b.

Disconnect the antenna connector from the quarter window assembly RH (window glass antenna wire).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - A-1 Always Below 1 Ω
B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 6 ANTENNA CORD SUB-ASSEMBLY

11.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

12.CHECK NO. 2 AMPLIFIER ANTENNA ASSEMBLY
12.CHECK NO. 2 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 2 amplifier antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (NO. 2 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG