Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.04–2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 4 Line (for RHD)  


DESCRIPTION

Symptom Trouble Area

*1: w/ Lane Tracing Assist System

*2: w/o Lane Tracing Assist System

There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen.
·

CAN bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No. 2 skid control ECU)

·

Power steering ECU with motor assembly*1

·

Airbag sensor with ECU assembly

·

Steering sensor

·

No. 1 CAN junction terminal*2

·

No. 2 global CAN junction connector

·

No. 10 global CAN junction connector



WIRING DIAGRAM

C460230E04
0.833,0.375 1.271,0.552 0.438,0.177 10 false CA2H 0.802,0.99 1.24,1.167 0.438,0.177 10 false CA2L 0.115,1.156 0.552,1.333 0.438,0.177 10 false I42 0.104,1.333 2.042,1.698 1.938,0.365 10 false Central Gateway ECU (Network Gateway ECU) 5.854,5.125 6.292,5.302 0.438,0.177 10 false I51 5.844,5.313 7.104,5.5 1.26,0.188 10 false Steering Sensor 5.229,1.104 5.667,1.281 0.438,0.177 10 false I100 5.573,7.104 7.063,7.51 1.49,0.406 10 false Airbag Sensor with ECU Assembly 0.208,5.042 0.646,5.219 0.438,0.177 10 false B20 0.115,3.292 2.323,3.885 2.208,0.594 10 false Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU) 5.594,6.875 6.031,7.052 0.438,0.177 10 false I24 0.198,5.24 1.771,5.74 1.573,0.5 10 false Brake Actuator Assembly (No. 2 Skid Control ECU) 0.146,3.115 0.583,3.292 0.438,0.177 10 false B19 2.063,5.354 2.5,5.531 0.438,0.177 10 false B49 2.063,5.542 3.719,6.021 1.656,0.479 10 false No. 2 Global CAN Junction Connector 3.74,7.188 4.177,7.365 0.438,0.177 10 false I123 3.729,7.375 4.938,7.948 1.208,0.573 10 false No. 10 Global CAN Junction Connector 5.969,4.49 6.406,4.667 0.438,0.177 10 false CANH 5.99,4.865 6.427,5.042 0.438,0.177 10 false CANL 5.948,6.302 6.385,6.479 0.438,0.177 10 false CAFH 5.969,6.667 6.396,6.844 0.427,0.177 10 false CAFL 0.823,2.51 1.26,2.688 0.438,0.177 10 false CA1H 0.854,2.875 1.281,3.052 0.427,0.177 10 false CA1L 0.823,4.458 1.26,4.635 0.438,0.177 10 false CANH 0.833,4.823 1.271,5 0.438,0.177 10 false CANL 1.323,0.365 1.583,0.542 0.26,0.177 10 false 24 1.313,0.781 1.573,0.958 0.26,0.177 10 false 23 5.771,4.354 6.031,4.531 0.26,0.177 10 false 3 5.76,4.75 6.021,4.927 0.26,0.177 10 false 8 5.688,6.135 5.948,6.313 0.26,0.177 10 false 26 5.677,6.583 5.938,6.76 0.26,0.177 10 false 27 1.302,4.333 1.563,4.51 0.26,0.177 10 false 27 1.302,4.729 1.563,4.906 0.26,0.177 10 false 43 1.313,2.396 1.573,2.573 0.26,0.177 10 false 38 1.313,2.802 1.573,2.979 0.26,0.177 10 false 39 2.5,0.344 2.708,0.542 0.208,0.198 10 false 2 2.5,0.771 2.708,0.969 0.208,0.198 10 false 8 3.25,0.344 3.458,0.542 0.208,0.198 10 false 1 3.271,0.75 3.479,0.948 0.208,0.198 10 false 7 2.51,2.365 2.719,2.563 0.208,0.198 10 false 3 2.5,2.781 2.708,2.979 0.208,0.198 10 false 9 2.51,4.323 2.719,4.521 0.208,0.198 10 false 4 2.448,4.719 2.656,4.917 0.208,0.198 10 false 10 4.656,0.354 4.865,0.552 0.208,0.198 10 false 2 4.635,0.75 4.844,0.948 0.208,0.198 10 false 13 4.698,4.344 4.906,4.542 0.208,0.198 10 false 3 4.688,4.74 4.896,4.938 0.208,0.198 10 false 14 3.906,0.354 4.115,0.552 0.208,0.198 10 false 1 3.844,0.74 4.052,0.938 0.208,0.198 10 false 12 6.063,0.406 6.5,0.583 0.438,0.177 10 false CANH 6.063,0.99 6.5,1.167 0.438,0.177 10 false CANL 5.75,0.781 5.958,0.979 0.208,0.198 10 false 2 5.76,0.365 5.969,0.563 0.208,0.198 10 false 3 0.281,8.24 3.583,8.479 3.302,0.24 10 false *1: w/o Lane Tracing Assist System 3.115,8.24 5.677,8.438 2.563,0.198 10 false *2: w/ Lane Tracing Assist System 5.229,0.344 5.438,0.542 0.208,0.198 10 false *1 5.219,0.74 5.427,0.938 0.208,0.198 10 false *1 4.656,6.573 4.865,6.771 0.208,0.198 10 false 15 4.688,6.135 4.896,6.333 0.208,0.198 10 false 4 5.188,2.333 5.396,2.531 0.208,0.198 10 false *2 5.177,2.729 5.385,2.927 0.208,0.198 10 false *2 5.729,2.333 5.896,2.531 0.167,0.198 10 false 7 5.729,2.74 5.896,2.938 0.167,0.198 10 false 8 6.031,2.365 6.469,2.542 0.438,0.177 10 false CANH 5.219,1.271 7.156,1.729 1.938,0.458 10 false No. 2 CAN Junction Terminal 6.01,2.969 6.448,3.146 0.438,0.177 10 false CANL 5.656,3.125 6.094,3.302 0.438,0.177 10 false I71 5.656,3.313 6.948,3.958 1.292,0.646 10 false Power Steering ECU with Motor Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

·

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-24 (CA2H) - I42-23 (CA2L) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS WIRES

NG

59.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS WIRES
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-24 (CA2H) - I42-23 (CA2L) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-24 (CA2H) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-23 (CA2L) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-24 (CA2H) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-23 (CA2L) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the B49 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-1 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B49-7 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-2 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B49-8 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-3 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B49-9 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-4 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B49-10 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I123 No. 10 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

10.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

10.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/o Lane Tracing Assist System A
w/ Lane Tracing Assist System B



A

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

B

12.CHECK VEHICLE TYPE
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

OK

12.CHECK VEHICLE TYPE

NG

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)
12.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Lane Tracing Assist System A
w/o Lane Tracing Assist System B



A

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

B

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

OK

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)

NG

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)
14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)

OK

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

OK

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

NG

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)
a.

Disconnect the I100 No. 1 CAN junction terminal connector.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)
a.

Disconnect the I71 power steering ECU with motor assembly connector.



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
a.

Disconnect the I24 airbag sensor with ECU assembly connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the I51 steering sensor connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-2 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B49-8 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-3 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B49-9 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Disconnect the B20 brake actuator assembly (No. 2 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-4 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B49-10 (CANL) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the B49 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-1 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B49-7 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-2 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B49-8 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-3 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B49-9 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-4 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B49-10 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I123 No. 10 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

28.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

28.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/o Lane Tracing Assist System A
w/ Lane Tracing Assist System B



A

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

B

30.CHECK VEHICLE TYPE
29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

OK

30.CHECK VEHICLE TYPE

NG

34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)
30.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Lane Tracing Assist System A
w/o Lane Tracing Assist System B



A

31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

B

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

OK

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)

NG

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)
32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)

OK

33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

OK

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

NG

37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)
a.

Disconnect the I100 No. 1 CAN junction terminal connector.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)
a.

Disconnect the I71 power steering ECU with motor assembly connector.



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
a.

Disconnect the I24 airbag sensor with ECU assembly connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)

37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the I51 steering sensor connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-2 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B49-8 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-3 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B49-9 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Disconnect the B20 brake actuator assembly (No. 2 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49,I76)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

B49-4 (CANH) -I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B49-10 (CANL) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the B49 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-1 (CANH) - B49-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-2 (CANH) - B49-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

NG

56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
43.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-3 (CANH) - B49-9 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

NG

57.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-4 (CANH) - B49-10 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

58.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the I123 No. 10 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-1 (CANH) - I123-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

46.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

46.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/o Lane Tracing Assist System A
w/ Lane Tracing Assist System B



A

47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

B

48.CHECK VEHICLE TYPE
47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-2 (CANH) - I123-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

48.CHECK VEHICLE TYPE

NG

52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)
48.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Lane Tracing Assist System A
w/o Lane Tracing Assist System B



A

49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

B

50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-2 (CANH) - I123-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)

NG

53.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)
50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-4 (CANH) - I123-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-3 (CANH) - I123-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

NG

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)
a.

Disconnect the I100 No. 1 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-2 (CANH) - I123-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

53.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)
a.

Disconnect the I71 power steering ECU with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-2 (CANH) - I123-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)
a.

Disconnect the I24 airbag sensor with ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-4 (CANH) - I123-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - AIRBAG SENSOR WITH ECU ASSEMBLY)

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the I51 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-3 (CANH) - I123-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - STEERING SENSOR)

56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-2 (CANH) - B49-8 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

57.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))
a.

Disconnect the B19 brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-3 (CANH) - B49-9 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU))

58.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))
a.

Disconnect the B20 brake actuator assembly (No. 2 skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-4 (CANH) -B49-10 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU))

59.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the B49 No. 2 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-1 (CANH) - B49-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

60.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

61.CHECK FOR OPEN IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
60.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B49)Location & Routing

Click Connector(B49)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>No. 2 Global CAN Junction Connector

B49-2 (CANH) - B49-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 GLOBAL CAN JUNCTION CONNECTOR

NG

66.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
61.CHECK FOR OPEN IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the B49 No. 2 global CAN junction connector.


b.

Disconnect the I123 No. 10 global CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-1 (CANH) - I123-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

62.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

62.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/o Lane Tracing Assist System A
w/ Lane Tracing Assist System B



A

63.CHECK FOR OPEN IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

B

64.CHECK VEHICLE TYPE
63.CHECK FOR OPEN IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-2 (CANH) - I123-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

64.CHECK VEHICLE TYPE

NG

67.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
64.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Lane Tracing Assist System A
w/o Lane Tracing Assist System B



A

65.CHECK FOR OPEN IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)

B

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

65.CHECK FOR OPEN IN CAN BUS WIRE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - POWER STEERING ECU WITH MOTOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I123)Location & Routing

Click Connector(I123)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 10 Global CAN Junction Connector

I123-2 (CANH) - I123-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

NG

68.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU WITH MOTOR ASSEMBLY - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
66.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the B49 No. 2 global CAN junction connector.


b.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-24 (CA2H) - I42-23 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 GLOBAL CAN JUNCTION CONNECTOR)

67.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I123 No. 10 global CAN junction connector.


b.

Disconnect the I100 No. 1 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I100)Location & Routing

Click Connector(I100)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 1 CAN Junction Terminal

I100-3 (CANH) - I100-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 1 CAN JUNCTION TERMINAL - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)

68.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU WITH MOTOR ASSEMBLY - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I123 No. 10 global CAN junction connector.


b.

Disconnect the I71 power steering ECU with motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I71)Location & Routing

Click Connector(I71)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

I71-7 (CANH) - I71-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (POWER STEERING ECU WITH MOTOR ASSEMBLY - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)