Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY (for Front Passenger Side) › from 2021.07
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467881 KNEE AIRBAG ASSEMBLY(for Front Passenger Side) A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY(for Front Passenger Side)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B664766N01
0.792,1.438 1.417,1.604 0.625,0.167 0.76,1.406 1.448,1.635 0.688,0.229 6.51,0.281 6.76,0.281 true 1.417,1.521 1.75,1.521 false 2.156,2.458 2.156,2.208 true 6.469,0.698 6.719,0.698 true 3.885,0.896 4.135,0.896 true 1.792,0.948 1.792,0.615 true 3.844,2 4.094,2 true 4.76,3.281 5.01,3.281 true 0.854,3.396 1.104,3.396 true 0.833,2.677 1.208,2.677 true 6.458,1.031 6.708,1.031 true 6.219,0.125 7.042,0.479 0.823,0.354 18 false 10 5.906,0.865 6.719,1.479 0.813,0.615 18 false 9, 11 6.313,0.542 6.594,0.896 0.281,0.354 18 false 8 5.021,3.135 5.302,3.49 0.281,0.354 18 false 6 2.083,2.427 2.365,2.781 0.281,0.354 18 false 7 4.146,0.75 4.698,1.104 0.552,0.354 18 false 4 4.104,1.865 4.656,2.219 0.552,0.354 18 false 5 1.427,2.573 1.979,2.927 0.552,0.354 18 false 3 1.135,3.24 1.688,3.594 0.552,0.354 18 false 2 1.719,0.344 2.271,0.698 0.552,0.354 18 false 1 1.896,1.417 2.354,1.615 0.458,0.198 10 false x 3 0.833,1.448 2.385,1.625 1.552,0.177 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 73990 (Click here) - -
2 INNER NO. 1 INSTRUMENT PANEL BRACKET COVER RH 55394D - - -
3 LOWER NO. 2 INSTRUMENT PANEL PAD SUB-ASSEMBLY 55403H (Click here) - -
4 NO. 1 INSTRUMENT SIDE PANEL 55317E - - -
5 COWL SIDE TRIM BOARD RH 62111C - - -
6 FRONT DOOR SCUFF PLATE RH 67913B - - -
7 NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55607 - - -
8 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL - (Click here) - -
9 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
10 CHECK SRS WARNING LIGHT - (Click here) - -
11 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 73990 1.INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

a.
B608600C01
0.583,0.667 1.167,0.667 true 4.208,0.094 4.531,0.417 0.323,0.323 18 false ii 0.438,0.563 0.708,0.771 0.271,0.208 10 false *a 0.625,0.094 0.948,0.417 0.323,0.323 18 false i
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B608762N01
0.542,0.031 0.823,0.385 0.281,0.354 18 false i 4.042,0.031 4.323,0.385 0.281,0.354 18 false ii 0.448,2.073 0.729,2.427 0.281,0.354 18 false iii 4.042,2.073 4.323,2.427 0.281,0.354 18 false iv

i.

Engage the claw and guide.


ii.

Install the lower No. 2 instrument panel airbag assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the airbag connector.

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

Make sure the lock button is securely locked.



HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



iv.

Check that there is no looseness in the lower No. 2 instrument panel airbag assembly.



Hide 55394D 2.INSTALL INNER NO. 1 INSTRUMENT PANEL BRACKET COVER RH

Hide 55403H 3.INSTALL LOWER NO. 2 INSTRUMENT PANEL PAD SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 55317E 4.INSTALL NO. 1 INSTRUMENT SIDE PANEL

Hide 62111C 5.INSTALL COWL SIDE TRIM BOARD RH

Hide 67913B 6.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 55607 7.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 9. PERFORM DIAGNOSTIC SYSTEM CHECK

Hide 11. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART