Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Center Pillar) › from 2021.07
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467878 SIDE AIRBAG SENSOR(for Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Center Pillar)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B608786N01
3.531,3.438 4.531,3.604 1,0.167 3.5,3.406 4.563,3.635 1.063,0.229 1.969,2.063 2.74,2.292 0.771,0.229 2,2.094 2.708,2.26 0.708,0.167 6.531,0.24 6.781,0.24 true 6.49,0.646 6.74,0.646 true 6.469,0.99 6.719,0.99 true 4.552,3.229 4.823,3.229 true 4.031,2.979 4.031,3.438 false 1.781,1.594 2.031,1.594 true 0.969,3.104 0.969,3.354 true 5.896,1.844 5.896,2.094 true 2.906,2.135 2.906,2.385 true 3.906,1.563 4.156,1.563 true 2.354,1.802 2.354,2.094 false 6.365,0.073 6.667,0.438 0.302,0.365 18 false 9 6.333,0.479 6.615,0.833 0.281,0.354 18 false 7 0.906,2.833 1.188,3.188 0.281,0.354 18 false 6 1.615,1.417 1.896,1.771 0.281,0.354 18 false 4 5.823,1.573 6.104,1.927 0.281,0.354 18 false 5 4.417,1.427 4.698,1.781 0.281,0.354 18 false 2 2.844,2.344 3.125,2.698 0.281,0.354 18 false 3 5.083,3.073 5.365,3.427 0.281,0.354 18 false 1 5.885,0.823 6.531,1.219 0.646,0.396 18 false 8, 10 3.583,3.448 4.75,3.604 1.167,0.156 8 false 9.0 (92, 80 in.*lbf) 2.052,2.104 2.771,2.281 0.719,0.177 8 false 42 (428, 31)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FLOOR SIDE AIRBAG SENSOR LH 89831E (Click here) - -
2 CENTER PILLAR LOWER GARNISH LH 62414A (Click here) - -
3 FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) 73220 - - -
4 OUTER LAP BELT ANCHOR COVER 73233 - - -
5 REAR DOOR SCUFF PLATE LH 67918D - - -
6 FRONT DOOR SCUFF PLATE LH 67914B - - -
7 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL - (Click here) - -
8 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
9 CHECK SRS WARNING LIGHT - (Click here) - -
10 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89831E 1.INSTALL FLOOR SIDE AIRBAG SENSOR LH

a.
B608600C01
0.583,0.667 1.167,0.667 true 4.208,0.094 4.531,0.417 0.323,0.323 18 false ii 0.438,0.563 0.708,0.771 0.271,0.208 10 false *a 0.625,0.094 0.948,0.417 0.323,0.323 18 false i
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B608788N01
0.417,0.073 0.698,0.427 0.281,0.354 18 false i 1.948,0 2.688,0.563 0.74,0.563 18 false 1, 2 0.542,2.073 0.771,2.396 0.229,0.323 18 false 3 4.042,2.073 4.271,2.396 0.229,0.323 18 false 4

i.

Perform the following procedure to install the floor side airbag sensor LH.

1. Engage the claw to hold the floor side airbag sensor LH in place.

NOTICE:
·

If the floor side airbag sensor LH has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the floor side airbag sensor LH, make sure that the wire harness does not interfere with or is not pinched between other parts.

·

Make sure that the floor side airbag sensor LH claw is securely inserted into the body hole.



2. Install the floor side airbag sensor LH with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Tighten the bolt while holding the floor side airbag sensor LH because the floor side airbag sensor LH claw is easily damaged.


3. Check that there is no looseness in the installation parts of the floor side airbag sensor LH.

4. Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




Hide 62414A 2.INSTALL CENTER PILLAR LOWER GARNISH LH

Z101186

Click here(Click here)

Hide 73220 3.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

Hide 73233 4.INSTALL OUTER LAP BELT ANCHOR COVER

Hide 67918D 5.INSTALL REAR DOOR SCUFF PLATE LH

Hide 67914B 6.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 8. PERFORM DIAGNOSTIC SYSTEM CHECK

Hide 10. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART