| *A | w/ Courtesy Light | *B | w/ Reflex Reflector Assembly |
| *C | w/ Cover | - | - |
| *A | for LH Side | - | - |
| *1 | Wire Harness | *2 | Hole Plug |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
1. PRECAUTION
|
|
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
|
|
for 1GR-FE:
for V35A-FTS:
for F33A-FTV:
67786D 3.REMOVE REAR DOOR TRIM UPPER COVER
Using a moulding remover A, disengage the claws and remove the rear door trim upper cover.
4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Using a moulding remover A, disengage the claws and remove the rear power window regulator switch assembly with rear door armrest base panel.
Disconnect the connector.
81580C 6.REMOVE REFLEX REFLECTOR ASSEMBLY (w/ Reflex Reflector Assembly)
Apply protective tape as shown in the illustration.
Using a moulding remover A, disengage the claw.
Disengage the guide as shown in the illustration.
Disconnect the connector and remove the reflex reflector assembly.
67812C 7.REMOVE REAR DOOR HOLE COVER (w/ Cover)
Apply protective tape as shown in the illustration.
Using a moulding remover A, disengage the claw.
Disengage the guide as shown in the illustration.
Disconnect the connector and remove the rear door hole cover.
67604 8.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
| *A | for 14 Speakers | - | - |
|
Place Hands Here |
|
Remove in this Direction |
69206C 9.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
67674A 10.REMOVE REAR DOOR FRAME GARNISH
Using a clip remover with its tip wrapped in protective tape, detach the clip and remove the rear door frame garnish.
68174A 11.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction | - | - |
68197A 12.REMOVE REAR DOOR FRONT BELT SEAL
68199 13.REMOVE REAR DOOR REAR BELT SEAL
|
Remove in this Direction | - | - |
67842E 14.REMOVE REAR DOOR SERVICE HOLE COVER
| *A | for LH Side | - | - |
Disconnect the 2 connectors.
Disengage the clamps.
for LH Side:
1. Remove the bolt and wire harness.
Using a clip remover with its tip wrapped in protective tape, disengage the clips and remove the rear door service hole cover.
Pull out the rear door lock remote control cable assembly and rear door inside locking cable assembly from the rear door service hole cover as shown in the illustration.
68152C 15.REMOVE REAR DOOR GLASS RUN
67888F 16.REMOVE NO. 2 REAR DOOR WEATHERSTRIP
Using a clip remover with its tip wrapped in protective tape, disengage the clip and remove the No. 2 rear door weatherstrip.
67408E 17.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 5.0 mm (0.197 in.) | - | - |
Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.
Lightly press the drill against the rivet to drill off the rivet flange, and remove the rivet.
Be careful of the drilled rivet, as they may be hot.
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Prying the rivet with the rivet with the may damage the rivet installation hole or drill bit.
Remove the 2 bolts and remove the rear door window division bar sub-assembly.
68104 18.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Remove the hole plug.
Connect the connector to the power window regulator switch assembly with rear door armrest base panel.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Move the rear door glass sub-assembly until the bolts appear in the service holes.
Turn the ignition switch off.
|
Remove in this Direction | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the connector from the power window regulator switch assembly with rear door armrest base panel.
Remove the 2 bolts.
Remove the rear door glass sub-assembly as shown in the illustration.
Do not damage the rear door glass sub-assembly.
68124C 19.REMOVE REAR DOOR QUARTER WINDOW GLASS
|
Remove in this Direction | - | - |
68189 20.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP
69804 21.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
|
Remove in this Direction | - | - |
69032 23.REMOVE DOOR LOCK COVER SET
69240 25.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws.
Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.
Disengage the claws and move the lever as shown in the illustration.
Remove the rear door outside handle assembly as shown in the illustration.
69227M 26.REMOVE REAR DOOR OUTSIDE HANDLE COVER
Using a T30 "TORX" socket wrench, loosen the TORX screw.
The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.
Disengage the 2 claws to remove the rear door outside handle cover.
69241G 27.REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD
69242G 28.REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD
69204A 29.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the guides to remove the rear door outside handle frame sub-assembly as shown in the illustration.
Disengage the clamp.
68640A 30.REMOVE REAR DOOR CHECK ASSEMBLY
67872 31.REMOVE REAR DOOR WEATHERSTRIP
|
Double-sided Tape | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the clips.
Remove the double-sided tape with rear door weatherstrip from rear door panel.
Remove any remaining double-sided tape from the rear door panel.
67898G 33.REMOVE REAR NO. 4 DOOR WEATHERSTRIP
Using a screwdriver with its tip wrapped in protective tape, disengage the clip.
Disengage the guide to remove the rear door no. 4 weatherstrip.
75078 37.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY
67923B 38.REMOVE REAR DOOR NO. 1 STIFFENER CUSHION
67858B 39.REMOVE REAR DOOR PANEL PROTECTOR
Using a screwdriver with its tip wrapped in protective tape, disengage the claws and remove the rear door panel protector.
67837C 40.REMOVE REAR DOOR DUST PROOF SEAL
41.REMOVE HOLE PLUG