| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P052012 | Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery | Conditions (a) and (b) continue for 5 seconds or more: (a) Ignition switch is ON. (b) Oil pressure sender gauge assembly voltage is 4.78 V or higher. (1 trip detection logic) |
·
Open or short in oil pressure sender gauge assembly circuit
·
Oil pressure sender gauge assembly
·
ECM |
Comes on | SAE Code: P0523 |
| P052014 | Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open | Conditions (a) and (b) continue for 5 seconds or more: (a) Ignition switch is ON. (b) Oil pressure sender gauge assembly voltage is 0.23 V or less. (1 trip detection logic) |
·
Open or short in oil pressure sender gauge assembly circuit
·
Oil pressure sender gauge assembly
·
ECM |
Comes on | SAE Code: P0522 |
| DTC No. | Data List |
|---|---|
| P052012 P052014 |
Engine Oil Pressure |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P052012 P052014 |
Idling for 5 seconds or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the oil pressure sender gauge assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C168,C138)Location & Routingewd_type=routing;type=c,c;code=C168,C138 |
||
| C168-3 (VC) - C138-119 (VCPE) | Always | Below 1 Ω |
| C168-2 (POUT) - C138-74 (PEO) | Always | Below 1 Ω |
| C168-1 (E2) - C138-120 (EPEO) | Always | Below 1 Ω |
| C168-3 (VC) or C138-119 (VCPE) - Body ground and other terminals | Always | 10 kΩ or higher |
| C168-2 (POUT) or C138-74 (PEO) - Body ground and other terminals | Always | 10 kΩ or higher |
| C168-1 (E2) or C138-120 (EPEO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the oil pressure sender gauge assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C168)Location & Routingewd_type=routing;type=c;code=C168 |
||
| C168-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| C168-2 (POUT) - Body ground | Ignition switch ON | Below 0.1 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C168)Location & Routingewd_type=routing;type=c;code=C168 |
||
| C168-2 (POUT) - C168-1 (GND) | Ignition switch off | No short or no open circuit |
| C168-1 (GND) - Body ground | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sender gauge assembly.
Click hereEngine / Hybrid System>F33A-FTV (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and idle it for 5 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P052012 or P052014 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT