A fuel pressure sensor, which is built into the injector assembly, converts the fuel pressure to an electrical signal which is sent to the ECM. Based on this signal, the ECM controls the fuel supply pump assembly and maintains the fuel pressure in the common rail assembly at the target pressure. A semiconductor is used in the fuel pressure sensor. The semiconductor changes its internal resistance value according to the fuel pressure, and as a result, the output voltage is proportional to the fuel pressure.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P13A011 | Fuel Pressure Sensor #1(Sub CPU) Circuit Short to Ground | Sub CPU Side: The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13A1 |
| P13A015 | Fuel Pressure Sensor #1(Sub CPU) Circuit Short to Battery or Open | Sub CPU Side: The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13A2 |
| P13A02A | Fuel Pressure Sensor #1(Sub CPU) Signal Stuck in Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13A3 |
| P13A511 | Fuel Pressure Sensor #2(Sub CPU) Circuit Short to Ground | Sub CPU Side: The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13A6 |
| P13A515 | Fuel Pressure Sensor #2(Sub CPU) Circuit Short to Battery or Open | Sub CPU Side: The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13A7 |
| P13A52A | Fuel Pressure Sensor #2(Sub CPU) Signal Stuck in Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13A8 |
| P13AA11 | Fuel Pressure Sensor #3(Sub CPU) Circuit Short to Ground | Sub CPU Side: The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13AB |
| P13AA15 | Fuel Pressure Sensor #3(Sub CPU) Circuit Short to Battery or Open | Sub CPU Side: The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13AC |
| P13AA2A | Fuel Pressure Sensor #3(Sub CPU) Signal Stuck in Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13AD |
| P13B011 | Fuel Pressure Sensor #4(Sub CPU) Circuit Short to Ground | Sub CPU Side: The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13B1 |
| P13B015 | Fuel Pressure Sensor #4(Sub CPU) Circuit Short to Battery or Open | Sub CPU Side: The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13B2 |
| P13B02A | Fuel Pressure Sensor #4(Sub CPU) Signal Stuck in Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13B3 |
| P13B511 | Fuel Pressure Sensor #5 (Sub CPU) Circuit Short to Ground | Sub CPU Side: The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13B6 |
| P13B515 | Fuel Pressure Sensor #5 (Sub CPU) Circuit Short to Battery or Open | Sub CPU Side: The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13B7 |
| P13B52A | Fuel Pressure Sensor #5 (Sub CPU) Signal Stuck In Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13B8 |
| P13BA11 | Fuel Pressure Sensor #6 (Sub CPU) Circuit Short to Ground | Sub CPU Side: The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13BB |
| P13BA15 | Fuel Pressure Sensor #6 (Sub CPU) Circuit Short to Battery or Open | Sub CPU Side: The output voltage of the fuel pressure sensor is 4.76 V or higher for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13BC |
| P13BA2A | Fuel Pressure Sensor #6 (Sub CPU) Signal Stuck In Range | The output of the fuel pressure sensor differs by 42 MPa or more compared to other cylinders for 0.5 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13BD |
| P13E011 | Fuel Pressure Sensor #1(Main CPU) Circuit Short to Ground | Main CPU Side: The fuel pressure sensor output voltage of injector #1 and/or #4 is below 0.55 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13E1 |
| P13E015 | Fuel Pressure Sensor #1(Main CPU) Circuit Short to Battery or Open | Main CPU Side: The fuel pressure sensor output voltage of injector #1 and/or #4 is higher than 4.76 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13E2 |
| P13E511 | Fuel Pressure Sensor #4(Main CPU) Circuit Short to Ground | Main CPU Side: The fuel pressure sensor output voltage of injector #1 and/or #4 is below 0.55 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13E6 |
| P13E515 | Fuel Pressure Sensor #4(Main CPU) Circuit Short to Battery or Open | Main CPU Side: The fuel pressure sensor output voltage of injector #1 and/or #4 is higher than 4.76 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in fuel pressure sensor (built into injector assembly) circuit
·
Fuel pressure sensor (built into injector assembly)
·
ECM |
Comes on | SAE Code: P13E7 |
| DTC No. | Data List |
|---|---|
| P13A011 P13A015 P13A511 P13A515 P13AA11 P13AA15 P13B011 P13B015 P13B511 P13B515 P13BA11 P13BA15 |
·
Fuel Pressure #1
·
Fuel Pressure #2
·
Fuel Pressure #3
·
Fuel Pressure #4
·
Fuel Pressure #5
·
Fuel Pressure #6 |
| P13E011 P13E015 P13E511 P13E515 |
|
| P13A02A P13A52A P13AA2A P13B02A P13B52A P13BA12 |
Check Common Rail Pressure and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Target Fuel Pressure (High). Under stable conditions, the difference between "Fuel Pressure (High)" and "Target Fuel Pressure (High)" is 3500 kPag or less.
If DTC P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13B511, P13B515, P13B52A, P13BA11, P13BA15, P13BA2A, P13E011, P13E015, P13E511 and/or P13E515 is stored, the following symptom may appear:
Lack of power due to accelerator restriction performed by fail-safe function
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P13A011 P13A015 P13A511 P13A515 P13AA11 P13AA15 P13B011 P13B015 P13B511 P13B515 P13BA11 P13BA15 |
Ignition switch ON for 1 second or more |
| P13E011 P13E015 P13E511 P13E515 |
Ignition switch ON for 8 seconds or more |
| P13A02A P13A52A P13AA2A P13B02A P13B52A P13BA2A |
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds |
If the fuel pressure sensor output voltage is outside of the standard range due to an open or short in the fuel pressure sensor circuit, DTCs are stored.
If a DTC is stored, the ECM enters fail-safe mode, and engine output is limited only if 2 or more circuits are malfunctioning. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
The No. 1 injector assembly and No. 4 injector assembly have separate circuits inside the ECU and a fuel pressure sensor value is input to both the Main CPU and Sub CPU.
When there is an open circuit in EIJ or VIJ, DTC P13E015 and P13A015 are output at the same time.
If only one of them are output, there may be an open in the internal circuit of the ECM.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| "Fuel pressure sensor circuit DTC" and "Injector Internal EEPROM Malfunction circuit DTC" are output* | A |
| Except above | B |
*: Fuel pressure sensor circuit DTC and Injector Internal EEPROM Malfunction circuit DTC:
Fuel pressure sensor circuit DTC: P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13B511, P13B515, P13B52A, P13BA11, P13BA15, P13BA2A, P13E011, P13E015, P13E511, P13E515.
Injector Internal EEPROM Malfunction circuit DTC: P168A00, P168A44, P168A46, P168B00, P168B44, P168B46, P168C00, P168C44, P168C46, P168D00, P168D44, P168D46, P168E00, P168E44, P168E46, P168F00, P168F44, P168F46.
When there is an injector internal EEPROM malfunction, fuel pressure sensor (sub CPU) signal stuck in range and fuel temperature sensor circuit open DTCs are output at the same time.
For example, when P168A00, P168A44, P168A46 is output, P13A02A and P13C013 are output together.
A
B
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C117,C139,C118,C119,C120,C121,C122)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c;code=C117,C139,C118,C119,C120,C121,C122 |
||
| C117-2 (VIJ1) - C139-52 (VIJ1) | Always | Below 1 Ω |
| C117-4 (PIJ1) - C139-50 (PIJ1) | Always | Below 1 Ω |
| C117-1 (EIJ1) - C139-51 (EIJ1) | Always | Below 1 Ω |
| C118-2 (VIJ2) - C139-42 (VIJ2) | Always | Below 1 Ω |
| C118-4 (PIJ2) - C139-40 (PIJ2) | Always | Below 1 Ω |
| C118-1 (EIJ2) - C139-41 (EIJ2) | Always | Below 1 Ω |
| C119-2 (VIJ3) - C139-32 (VIJ3) | Always | Below 1 Ω |
| C119-4 (PIJ3) - C139-30 (PIJ3) | Always | Below 1 Ω |
| C119-1 (EIJ3) - C139-31 (EIJ3) | Always | Below 1 Ω |
| C120-2 (VIJ4) - C139-49 (VIJ4) | Always | Below 1 Ω |
| C120-4 (PIJ4) - C139-47 (PIJ4) | Always | Below 1 Ω |
| C120-1 (EIJ4) - C139-48 (EIJ4) | Always | Below 1 Ω |
| C121-2 (VIJ5) - C139-39 (VIJ5) | Always | Below 1 Ω |
| C121-4 (PIJ5) - C139-37 (PIJ5) | Always | Below 1 Ω |
| C121-1 (EIJ5) - C139-38 (EIJ5) | Always | Below 1 Ω |
| C122-2 (VIJ6) - C139-29 (VIJ6) | Always | Below 1 Ω |
| C122-4 (PIJ6) - C139-27 (PIJ6) | Always | Below 1 Ω |
| C122-1 (EIJ6) - C139-28 (EIJ6) | Always | Below 1 Ω |
| C117-2 (VIJ1) or C139-52 (VIJ1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C117-4 (PIJ1) or C139-50 (PIJ1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C118-2 (VIJ2) or C139-42 (VIJ2)) - Body ground and other terminals | Always | 10 kΩ or higher |
| C118-4 (PIJ2) or C139-40 (PIJ2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C119-2 (VIJ3) or C139-32 (VIJ3) - Body ground and other terminals | Always | 10 kΩ or higher |
| C119-4 (PIJ3) or C139-30 (PIJ3) - Body ground and other terminals | Always | 10 kΩ or higher |
| C120-2 (VIJ4) or C139-49 (VIJ4) - Body ground and other terminals | Always | 10 kΩ or higher |
| C120-4 (PIJ4) or C139-47 (PIJ4) - Body ground and other terminals | Always | 10 kΩ or higher |
| C121-2 (VIJ5) or C139-39 (VIJ5) - Body ground and other terminals | Always | 10 kΩ or higher |
| C121-4 (PIJ5) or C139-37 (PIJ5) - Body ground and other terminals | Always | 10 kΩ or higher |
| C122-2 (VIJ6) or C139-29 (VIJ6) - Body ground and other terminals | Always | 10 kΩ or higher |
| C122-4 (PIJ6) or C139-27 (PIJ6) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the injector assembly connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C117,C118,C119,C120,C121,C122)Location & Routingewd_type=routing;type=c,c,c,c,c,c;code=C117,C118,C119,C120,C121,C122 |
||
| C117-2 (VIJ1) - C117-1 (EIJ1) | Ignition switch ON | 4.5 to 5.5 V |
| C118-2 (VIJ2) - C118-1 (EIJ2) | Ignition switch ON | 4.5 to 5.5 V |
| C119-2 (VIJ3) - C119-1 (EIJ3) | Ignition switch ON | 4.5 to 5.5 V |
| C120-2 (VIJ4) - C120-1 (EIJ4) | Ignition switch ON | 4.5 to 5.5 V |
| C121-2 (VIJ5) - C121-1 (EIJ5) | Ignition switch ON | 4.5 to 5.5 V |
| C122-2 (VIJ6) - C122-1 (EIJ6) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector assembly of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL
Replace the injection pipe sub-assembly that was removed with a new one.
Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Perform the following when there are DTCs which are not cleared.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and wait for 8 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes / Clear.
Check that all DTCs have been cleared.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and wait for 8 seconds or more.
Start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT