Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P006900  Manifold Absolute Pressure - Barometric Pressure Correlation  


DESCRIPTION

To detect atmospheric pressure, the atmospheric pressure sensor built into the ECM is used in the common rail system. Following the changes in the atmospheric pressure, the ECM corrects the fuel injection volume, timing and duration, and adjusts the common rail internal fuel pressure to optimize combustion.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P006900 Manifold Absolute Pressure - Barometric Pressure Correlation After the ignition switch is turned to ON, the difference between the atmospheric pressure sensor output and manifold absolute pressure sensor output is more than 14 kPa for 0.5 seconds.
(2 trip detection logic)
·

Manifold absolute pressure sensor

·

ECM


Comes on SAE Code: P0069

Related Data List
DTC No. Data List
P006900
·

Atmospheric Pressure

·

Intake Manifold Absolute Pressure



HINT:
·

Turn the ignition switch to ON and check the "Atmospheric Pressure" and "Intake Manifold Absolute Pressure" items in the Data List. If the atmospheric pressure displayed on the GTS differs greatly from the actual atmospheric pressure (standard: 101 kPa), the sensor (atmospheric pressure sensor or manifold absolute pressure sensor) is malfunctioning.

·

If DTC P006900 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P006900 1 second elapses after ignition switch turned from off to ON (starter remains off)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P006900)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P006900 is output A
DTC P006900 and other DTCs are output B


HINT:

If codes other than DTC P006900 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR

B

GO TO DTC CHART

2.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR
HINT:

Before inspecting the manifold absolute pressure sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.


a.

Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Intake Manifold Absolute Pressure
50003 372 385

b.

Read the value.

OK:

Same value as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

4.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Turn the ignition switch to ON and wait for 1 second or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTC P006900 is output A
No DTC is output B



A

B

END

4.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR

OK

3.CHECK DTC OUTPUT

NG