The DC motor type No. 2 EGR valve assembly (EGR cooler bypass valve) consecutively changes the position of the EGR cooler route and bypass route, and sets an arbitrary EGR temperature.
The actual EGR gas temperature is measured by the EGR gas temperature sensor, and the position of the No. 2 EGR valve assembly (EGR cooler bypass valve) is fed back by the position sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P245A18 | Exhaust Gas Recirculation Cooler Bypass Control Circuit Low Bank 1 Circuit Current Below Threshold | Both of the following conditions are met for 2.0 seconds:
·
The EGR cooler bypass control valve actuator duty cycle is 80% or higher.
·
The EGR cooler bypass control valve actuator current is less than 0.5 A. (1 trip detection logic) |
·
Open or short in EGR cooler bypass control valve actuator circuit
·
No. 2 EGR valve assembly (EGR cooler bypass valve)
·
ECM |
Comes on | SAE Code: P245C |
| P245A19 | Exhaust Gas Recirculation Cooler Bypass Control Circuit High Bank 1 Circuit Current Above Threshold | Either of the following conditions is met for 2.0 seconds:
·
EGR cooler bypass control valve actuator current of 8 A or higher is detected.
·
The ECM internal circuit temperature of 150°C (302°F) or higher is detected. (1 trip detection logic) |
·
Open or short in EGR cooler bypass control valve actuator circuit
·
No. 2 EGR valve assembly (EGR cooler bypass valve)
·
ECM |
Comes on | SAE Code: P245D |
| DTC No. | Data List |
|---|---|
| P245A18 P245A19 |
·
EGR Cooler Bypass Valve Duty Ratio
·
EGR Cooler Bypass Valve Motor Current |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P048718 P048719 |
Bypass and Cooler are held for 5 seconds or more when the Active Test "Activate the EGR Cooler Bypass Control Valve" is performed. |
Refer to DTC P249211.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P249211
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Remove the No. 2 EGR valve assembly (EGR cooler bypass valve).
| *a | Component without harness connected (No. 2 EGR Control Valve Assembly (EGR cooler bypass valve)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - 6 | Always | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C130,C138)Location & Routingewd_type=routing;type=c,c;code=C130,C138 |
||
| C130-6 (ECM+) - C138-4 (ECM+) | Always | Below 1 Ω |
| C130-5 (ECM-) - C138-23 (ECM-) | Always | Below 1 Ω |
| C130-6 (ECM+) or C138-4 (ECM+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C130-5 (ECM-) or C138-23 (ECM-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Bypass and Cooler are held for 5 seconds or more when the Active Test "Activate the EGR Cooler Bypass Control Valve" is performed.
| Tester Display |
|---|
| Activate the EGR Cooler Bypass Control Valve |
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 2 EGR valve assembly (EGR cooler bypass valve).
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT