Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P05042B  Brake Switch "A"/"B" Signal Cross Coupled  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, Data List items Stop Light SW is ON when the brake pedal is depressed.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P05042B Brake Switch "A"/"B" Signal Cross Coupled Conditions (a) and (b) continue for 0.5 seconds or more:
(a) Ignition switch is ON.
(b) STP signal OFF when ST1- signal is off.
(1 trip detection logic)
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Does not come on SAE Code: P0504

Related Data List
DTC No. Data List
P05042B Stop Light SW

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P05042B Depress and release brake pedal with ignition switch ON

WIRING DIAGRAM

A485841E02
0.521,4.031 1.135,4.26 0.615,0.229 10 false Battery 0.615,1.208 1.021,1.708 0.406,0.5 10 false MAIN R/B 2.615,0.573 3.229,0.802 0.615,0.229 10 false PDB-B 1.573,4.135 3.75,4.51 2.177,0.375 10 false Certification ECU (Smart Key ECU Assembly) 2.375,3.354 2.802,3.615 0.427,0.26 10 false IGPD 2.823,3.198 3.188,3.427 0.365,0.229 10 false 24 1.594,3.948 1.958,4.177 0.365,0.229 10 false I40 1.74,1.823 2.531,2.063 0.792,0.24 10 false IGP NO. 1 3.573,0.594 4.021,0.875 0.448,0.281 10 false STOP 1.729,1.458 2.094,1.688 0.365,0.229 10 false 2 1.719,0.927 1.906,1.115 0.188,0.188 10 false 3 2.344,0.927 2.531,1.115 0.188,0.188 10 false 5 2.344,1.458 2.531,1.646 0.188,0.188 10 false 1 4.656,1.875 5.021,2.104 0.365,0.229 10 false B43 4.646,2.052 5.75,2.427 1.104,0.375 10 false Stop Light Switch Assembly 4.677,1.563 5.042,1.792 0.365,0.229 10 false GND 4.698,0.448 5.063,0.677 0.365,0.229 10 false B 4.708,1.052 5.073,1.281 0.365,0.229 10 false B 5.281,0.427 5.469,0.688 0.188,0.26 10 false L 5.271,1.021 5.458,1.281 0.188,0.26 10 false L 4.5,0.313 4.688,0.5 0.188,0.188 10 false 7 4.5,0.885 4.667,1.115 0.167,0.229 10 false 6 4.5,1.406 4.667,1.635 0.167,0.229 10 false 2 5.5,0.302 5.688,0.49 0.188,0.188 10 false 3 5.5,0.896 5.688,1.083 0.188,0.188 10 false 5 5.823,0.302 6.01,0.49 0.188,0.188 10 false 22 5.833,0.927 6.021,1.115 0.188,0.188 10 false 21 6.094,0.302 6.448,0.5 0.354,0.198 10 false STP 6.094,0.917 6.448,1.115 0.354,0.198 10 false ST1- 6.375,3.938 6.729,4.135 0.354,0.198 10 false B70 6.385,4.125 6.74,4.323 0.354,0.198 10 false ECM 2.469,1.219 3.646,1.396 1.177,0.177 10 false ECU-IGP NO. 3 0.698,0.542 0.885,0.729 0.188,0.188 10 false *2 0.365,1.167 0.552,1.354 0.188,0.188 10 false *1 0.677,2.458 1.615,2.708 0.938,0.25 10 false *1: for RHD 0.688,2.771 1.625,3.021 0.938,0.25 10 false *2: for LHD 1.135,1.177 1.323,1.365 0.188,0.188 10 false *1 3.885,0.292 4.052,0.51 0.167,0.219 10 false 2 3.021,0.292 3.188,0.51 0.167,0.219 10 false 2 2.99,0.906 3.156,1.125 0.167,0.219 10 false 2 3.438,0.302 3.677,0.51 0.24,0.208 10 false 1 2.552,0.302 2.792,0.51 0.24,0.208 10 false 1 2.583,0.906 2.823,1.115 0.24,0.208 10 false 1

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON and turn the GTS on.

(c)

Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.

(d)

Check Stop Light SW when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL VOLTAGE)
a.

Disconnect the stop light switch connector.


b.

Turn the ignition switch to ON


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B43)Location & Routing

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

B43-6 (B) - Body ground Ignition switch ON 11 to 14 V
B43-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY, IGP NO. 1 RELAY)

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B43)Location & Routing

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

B43-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (STP AND ST1- VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition

Click Location & Routing(B70)Location & Routing

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B70-21 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
B70-22 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B43,B70)Location & Routing

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B43-3 (L) - B70-22 (STP) Always Below 1 Ω
B43-5 (L) - B70-21 (ST1-) Always Below 1 Ω
B43-3 (L) or B70-22 (STP) - Body ground and other terminals Always 10 kΩ or higher
B43-5 (L) or B70-21 (ST1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR