Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P056014  System Voltage Circuit Short to Ground or Open  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P056014 System Voltage Circuit Short to Ground or Open The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized.
(1 trip detection logic)
·

Open in backup power source circuit (to BATT terminal)

·

Battery

·

Battery terminals

·

ECM


Comes on SAE Code: P0562

Related Data List
DTC No. Data List
P056014 BATT Voltage*

*: This is not the voltage at terminal BATT, it is the power supply voltage for the ECM.

HINT:

If DTC P056014 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P056014 Ignition switch ON for 3 seconds or more

WIRING DIAGRAM

A490663E01
0.896,1.906 1.5,2.135 0.604,0.229 10 false Battery 0.781,1.208 2,1.469 1.219,0.26 10 false SUB R/B NO. 1 2.75,0.875 4.073,1.25 1.323,0.375 10 false EFI MAIN NO. 1 5.771,0.698 6.375,0.927 0.604,0.229 10 false BATT 5.792,1.635 6.396,1.865 0.604,0.229 10 false E1 4.354,0.552 4.49,0.781 0.135,0.229 10 false 1 4.729,0.552 4.865,0.781 0.135,0.229 10 false 2 5.563,0.573 5.698,0.802 0.135,0.229 10 false 1 5.49,1.51 5.76,1.708 0.271,0.198 10 false 10 6.052,2.406 6.552,2.646 0.5,0.24 10 false ECM 6.052,2.24 6.51,2.438 0.458,0.198 10 false B70 4.313,0.906 5.635,1.281 1.323,0.375 10 false EFI NO. 2 2.917,0.594 3.052,0.823 0.135,0.229 10 false 1 3.333,0.594 3.469,0.823 0.135,0.229 10 false 2 1.458,0.885 2.781,1.26 1.323,0.375 10 false R/B NO. 2 1.552,0.615 1.688,0.844 0.135,0.229 10 false 1 1.938,0.604 2.073,0.833 0.135,0.229 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

2.CHECK BATTERY TERMINAL

NG

9.RECHARGE OR REPLACE BATTERY
2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

3.CHECK ECM TERMINAL VOLTAGE (BATT)

NG

7.REPAIR OR REPLACE BATTERY TERMINAL
3.CHECK ECM TERMINAL VOLTAGE (BATT)
a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B70)Location & Routing

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B70-1 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P056014 is output A
No DTC is output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE BATTERY TERMINAL
a.

Repair or replace the battery terminal.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED