Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P122900  Fuel Pump Valve Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P122900 Fuel Pump Valve Malfunction The actual fuel pressure exceeds the target fuel pressure by 3500 kPag or higher for 30 seconds.
(1 trip detection logic)
·

Short in pre-stroke control valve circuit

·

Fuel supply pump assembly

·

ECM


Comes on SAE Code: P1229

Related Data List
DTC No. Data List
P122900
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)



HINT:
·

When DTC P122900 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Target Fuel Pressure (High).

Under a stable condition such as idling after warming up the engine, Fuel Pressure (High) is within 3500 kPag of Target Fuel Pressure (High) when normal.

·

This DTC is stored when the actual fuel pressure in the common rail assembly is higher than the target fuel pressure, even though a signal is not being output from the ECM to operate the pre-stroke control valve.

This DTC indicates that the pre-stroke control valve may be stuck or have a short circuit.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P122900 Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.

MONITOR DESCRIPTION

This DTC is stored when the actual fuel pressure in the common rail assembly is higher than the target fuel pressure, even though a signal is not being output from the ECM to drive the pre-stroke control valve. This DTC indicates that the pre-stroke control valve may be stuck or have a short circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P122900 and/or DTCs related to the crankshaft position sensor circuit*1, fuel pressure sensor circuit*2, pre-stroke control valve circuit*3 , pressure discharge valve circuit*4 are output B
Except above A


HINT:
·

*1: Crankshaft position sensor circuit DTC: P033511, P033515, P03351F, P03352A, P033531.

·

*2: Fuel pressure sensor circuit DTC: P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13B511, P13B515, P13B52A, P13BA11, P13BA15, P13BA2A, P13E011, P13E015, P13E511, P13E515.

·

*3: Pre-stroke control valve circuit DTC: P062712, P062714, P263212, P263214.

·

*4: Pressure discharge valve circuit DTC: P127112, P127114, P127273.





A

2.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND TARGET FUEL PRESSURE (HIGH))

B

GO TO DTC CHART

2.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND TARGET FUEL PRESSURE (HIGH))
a.

Start the engine and warm it up.


b.

Enter the following menus: Powertrain / Engine / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Target Fuel Pressure (High)
Fuel Pressure (High)
50003 372 264,265

c.

Check that the internal fuel pressure of the common rail assembly is within the specification below.

OK:

Fuel Pressure (High) is within 3500 kPag of Target Fuel Pressure (High) when engine is idling after warming up the engine.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PRE-STROKE CONTROL VALVE)
3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PRE-STROKE CONTROL VALVE)
a.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Pre-stroke Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the Pre-stroke Control Valve
50004 372 42022

b.

Perform the Active Test and check that operation sounds can be heard from the pre-stroke control valve.

HINT:
·

Perform this procedure with the engine stopped and check the operation sounds from outside the vehicle.

·

Check in a quiet location with the hood opened, as the operation sound is difficult to hear.

·

In order to distinguish between the operation sounds of other actuators, check by using the GTS to turn the Active Test open and close several times.

·

This vehicle has 2 pre-stroke valve systems that operate alternately in 0.5 second intervals.

·

If the operating sound interval is larger than that of a normal vehicle, there may be a malfunction in one of the pre-stroke valves.



OK:

The operation sound is generated when performing the Active Test, and stops when finished.



Result:
Proceed to
OK
NG



OK

4.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
4.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL FILTER (for Fuel Tank Side)>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine.


d.

Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
DTC P122900 is output B




A

END

B

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY
6.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C166,C138,C167)Location & Routing

Click Connector(C166)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Pre-stroke Control Valve (Injection or Supply Pump Assembly)

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C167)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 2 Pre-stroke Control Valve (Injection or Supply Pump Assembly)

C166-1 (+B) - C138-29 (PCV+) Always Below 1 Ω
C166-2 (PCV) - C138-30 (PCV-) Always Below 1 Ω
C167-1 (+B) - C138-8 (PV2+) Always Below 1 Ω
C167-2 (PCV2) - C138-9 (PV2-) Always Below 1 Ω
C166-1 (+B) or C138-29 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
C166-2 (PCV) or C138-30 (PCV-) - Body ground and other terminals Always 10 kΩ or higher
C167-1 (+B) or C138-8 (PV2+) - Body ground and other terminals Always 10 kΩ or higher
C167-2 (PCV2) or C138-9 (PV2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine.


d.

Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.


e.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P122900.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Fuel Pressure (High)
Fuel Pressure (High)
50004 372 42023 264,265

c.

Take a snapshot with the GTS during the Active Test.


d.

Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E76
3.604,2.427 3.719,1.948 3.719,1.948 3.792,1.948 false 4.604,2.583 4.948,2.323 4.948,2.323 5.031,2.323 false 3.438,2.635 3.479,1.833 3.479,1.833 3.427,1.833 false 3.688,3.271 3.563,4.188 3.563,4.188 3.708,4.188 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.313,3.198 1.854,3.469 1.542,0.271 10 false Fuel Pressure (High) 3.802,1.865 5.74,2.031 1.938,0.167 10 false Target Fuel Pressure (High) 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.115,2.417 2.885,2.99 0.771,0.573 10 false Less than 10000 kPag 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.073,2.208 6.583,2.719 1.51,0.51 10 false Abnormal Fuel Pressure (High) 2.677,1.042 3.354,1.24 0.677,0.198 10 false Test Start 4.458,1.042 5.125,1.24 0.667,0.198 10 false Test Stop 5.885,1.042 6.563,1.24 0.677,0.198 10 false Test Start 2.073,1.76 3.427,2.188 1.354,0.427 10 false Normal Fuel Pressure (High) 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 3.771,4.125 5.969,4.677 2.198,0.552 10 false Pressure Discharge Valve Abnormal Fuel Pressure (High)

Standard:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag.


HINT:
·

"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.

·

"Fuel Pressure (High)" is the actual fuel pressure.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag. B
Except above A




A

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY

B

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED