Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P203111  Exhaust Gas Temperature Sensor 2 Bank 1 Circuit Short to Ground  P203115  Exhaust Gas Temperature Sensor 2 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P054411.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P054411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P203111 Exhaust Gas Temperature Sensor 2 Bank 1 Circuit Short to Ground No. 2 exhaust gas temperature sensor output voltage is below 0.2 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in No. 2 exhaust gas temperature sensor circuit

·

No. 2 exhaust gas temperature sensor

·

ECM


Comes on SAE Code: P2032
P203115 Exhaust Gas Temperature Sensor 2 Bank 1 Circuit Short to Battery or Open No. 2 exhaust gas temperature sensor output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met:
·

After starting the engine, 11 minutes or more elapses

·

Coolant temperature is 70°C (158°F) or higher

·

The exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds.


(1 trip detection logic)
·

Open or short in No. 2 exhaust gas temperature sensor circuit

·

No. 2 exhaust gas temperature sensor

·

ECM


Comes on SAE Code: P2033

Related Data List
DTC No. Data List
P203111
P203115
Exhaust Temperature B1S2

HINT:
·

DTC P20CF00 (Exhaust fuel addition injector assembly malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.

·

When DTC P203111 and P203115 is output, check the downstream exhaust gas temperature indicated by "Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2" using the GTS.


Reference:
Condition Exhaust Temperature B1S2 No. 2 Exhaust Gas Temperature Sensor Condition
Idling with warm engine Constant at between 50 and 700°C (122 and 1292°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the No. 2 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P203111 Ignition switch ON for 3 seconds or more
P203115 Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), allowing 11 minutes to elapse after starting the engine and waiting for the exhaust gas temperature sensor to be 120°C (248°F) or more for 15 seconds.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Sensor 2 represents the sensor located upstream of the DPF catalytic converter.



PROCEDURE

1.READ VALUE USING GTS (EXHAUST TEMPERATURE B1S2)
a.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 372 1134

b.

Read the value.

Standard:

Same as the actual No. 2 exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling with warm engine), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Temperature Displayed Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) B
OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warmup), and varies after maintaining an engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C


HINT:
·

If there is a short circuit, the GTS will indicate 0°C (32°F).

·

If there is an open circuit, the GTS will indicate 1000°C (1832°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

8.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A494487C01
1.479,2.469 1.927,2.802 0.448,0.333 1.938,3.594 2.219,4.031 true 1.479,3.594 1.219,4 true 0.563,2.76 0.875,2.958 0.313,0.198 10 false *a 0.688,1.802 1,2 0.313,0.198 10 false *1 2.583,1.771 2.896,1.969 0.313,0.198 10 false *2 1.573,0.667 1.99,0.854 0.417,0.188 10 false THCI 2.208,4.094 2.656,4.313 0.448,0.219 10 false THCI 1.635,1.375 2.083,1.573 0.448,0.198 10 false E2 1.094,4.073 1.542,4.292 0.448,0.219 10 false E2 1.563,2.583 2.01,2.802 0.448,0.219 10 false C173
*1 No. 2 Exhaust Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor)


Disconnect the No. 2 exhaust gas temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THCI) of the No. 2 exhaust gas temperature sensor connector on the wire harness side.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 372 1134

d.

Read the value.

Standard:

1000°C (1832°F)



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
3.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)

OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine.


d.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), allowing 11 minutes to elapse after starting the engine and waiting for the exhaust gas temperature sensor to be 120°C (248°F) or more for 15 seconds.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

8.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A178587C05
0.792,1.594 1.104,1.792 0.313,0.198 10 false *1 2.698,1.677 3.01,1.875 0.313,0.198 10 false *2
*1 No. 2 Exhaust Gas Temperature Sensor
*2 ECM


Disconnect the No. 2 exhaust gas temperature sensor connector.


b.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 372 1134

c.

Read the value.

Standard:

0°C (32°F)



Result:
Proceed to
OK
NG



OK

9.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

NG

10.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
9.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)

OK

11.REPLACE ECM

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 3 seconds or more.


d.

Start the engine.


e.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), allowing 11 minutes to elapse after starting the engine and waiting for the exhaust gas temperature sensor to be 120°C (248°F) or more for 15 seconds.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

g.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END