Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P20CB12  Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Battery  P20CB14  Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P200C4B

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P200C4B

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P20CB12 Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Battery Either of the following conditions is met:
·

The drive circuit voltage is the threshold or higher for 3 seconds or more, even if there is no open circuit in the circuit when the exhaust fuel addition injector assembly circuit is operating

·

Overcurrent is detected in the drive circuit 11 times or more during exhaust fuel addition injector assembly circuit operation


(1 trip detection logic)
·

Short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on SAE Code: P20CE
P20CB14 Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Ground or Open Either of the following conditions is met:
·

Open circuit is detected in the drive circuit 11 times or more during exhaust fuel addition injector assembly circuit operation

·

The drive circuit voltage is the threshold or lower for 3 seconds or more when the exhaust fuel addition injector assembly circuit is not operating.


(1 trip detection logic)
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on SAE Code: P20CD

Related Data List
DTC No. Data List
P20CB12
P20CB14
Exhaust Aftertreatment Fuel Injection Valve Current-Carrying Request

HINT:

DTC P200C4B, P200E4B, P20CF00 and/or P24284B will be present if there is an open malfunction in the exhaust fuel addition injector assembly circuit.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CB12
P20CB14
PM forced regeneration

WIRING DIAGRAM

A445677E15
0.719,1.854 1.177,2.052 0.458,0.198 10 false C152 0.708,2.052 3.573,2.302 2.865,0.25 10 false Exhaust Fuel Addition Injector Assembly 1.76,0.531 2.219,0.729 0.458,0.198 10 false +B 1.729,1.198 2.188,1.396 0.458,0.198 10 false FIV 5.677,0.646 6.313,0.844 0.635,0.198 10 false FIV+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false FIV- 5.25,1.292 5.708,1.49 0.458,0.198 10 false C138 6.052,1.896 6.51,2.094 0.458,0.198 10 false ECM 2.083,0.531 2.542,0.729 0.458,0.198 10 false 2 2.094,1.188 2.552,1.385 0.458,0.198 10 false 1 5.333,0.427 5.792,0.625 0.458,0.198 10 false 27 5.344,1.094 5.802,1.292 0.458,0.198 10 false 28 5.25,0.625 5.708,0.823 0.458,0.198 10 false C138

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Inspect the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C152,C138)Location & Routing

Click Connector(C152)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Exhaust Fuel Addition Injector Assembly

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C152-2 (+B) - C138-27 (FIV+) Always Below 1 Ω
C152-1 (FIV) - C138-28 (FIV-) Always Below 1 Ω
C152-2 (+B) or C138-27 (FIV+) - Body ground and other terminals Always 10 kΩ or higher
C152-1 (FIV) or C138-28 (FIV-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.



e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END