Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P061512  Starter Relay Circuit Short to Battery  


DESCRIPTION

While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P061512 Starter Relay Circuit Short to Battery Conditions (a), (b) and (c) are met for 20 seconds:

(a) Vehicle speed is more than 20 km/h (12.4 mph).

(b) Engine speed is more than 1000 rpm.

(c) STA signal is on.


(1 trip detection logic)
·

ST NO. 1 relay circuit

·

Park/Neutral position switch assembly

·

ECM


Comes on SAE Code: P0617

Related Data List
DTC No. Data List
P061512 Starter SW

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P061512 Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

A494961E05
0.188,1.823 0.667,2.063 0.479,0.24 10 false I40 0.188,2.01 1.708,2.448 1.521,0.438 10 false Certification ECU (Smart Key ECU Assembly) 3.042,1.865 3.521,2.104 0.479,0.24 10 false C34 3.052,2.042 4.365,2.427 1.313,0.385 10 false Park/Neutral Position Switch Assembly 1.594,0.594 2.073,0.833 0.479,0.24 10 false 15 1.604,1.042 2.083,1.281 0.479,0.24 10 false 10 1.646,1.448 2.125,1.688 0.479,0.24 10 false 3 1.292,0.708 1.771,0.948 0.479,0.24 10 false NE 1.125,1.156 1.604,1.396 0.479,0.24 10 false STAR 1.198,1.552 1.677,1.792 0.479,0.24 10 false STA 5.854,0.708 6.333,0.948 0.479,0.24 10 false NEO 5.854,1.167 6.333,1.406 0.479,0.24 10 false NSW 5.531,0.542 6.01,0.781 0.479,0.24 10 false 31 5.531,1.021 6.01,1.26 0.479,0.24 10 false 30 5.833,3.958 6.313,4.198 0.479,0.24 10 false STA 5.552,3.792 6.031,4.031 0.479,0.24 10 false 25 6.229,4.479 6.656,4.719 0.427,0.24 10 false ECM 2.948,4.615 3.635,4.865 0.688,0.25 10 false ST NO. 1 2.688,5.135 3.167,5.375 0.479,0.24 10 false 1 2.156,5.125 2.635,5.365 0.479,0.24 10 false 3 2.146,5.927 2.625,6.167 0.479,0.24 10 false C155 1.396,6.292 1.875,6.531 0.479,0.24 10 false C154 0.552,7.042 1.031,7.281 0.479,0.24 10 false Battery 1.719,7.104 2.365,7.573 0.646,0.469 10 false Starter Assembly 3.167,1.458 3.646,1.698 0.479,0.24 10 false 5 4.073,1.458 4.552,1.698 0.479,0.24 10 false 4 3.854,1.469 4.333,1.708 0.479,0.24 10 false B 3.375,1.469 3.854,1.708 0.479,0.24 10 false L 2.177,4.135 2.656,4.375 0.479,0.24 10 false 5 2.698,4.135 3.177,4.375 0.479,0.24 10 false 2 2.563,5.896 3.042,6.135 0.479,0.24 10 false 1 1.521,6.083 2,6.323 0.479,0.24 10 false 1 0.375,4.802 1.5,5.021 1.125,0.219 10 false SUB R/B NO. 1 0.719,4.094 1.406,4.344 0.688,0.25 10 false ST NO. 1 1.844,6.146 2.323,6.385 0.479,0.24 10 false B 2.354,6.135 2.833,6.375 0.479,0.24 10 false ST 6.229,4.313 6.708,4.552 0.479,0.24 10 false B70

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
Standard:
Condition Starter SW
Ignition switch ON OFF



b.

According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12.43 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Standard:
Condition Starter SW
Driving at 20 km/h (12.43 mph) or more (engine speed 1000 rpm or more) OFF



HINT:

If the result of either of the above is not as specified, proceed to the next step with the ignition switch ON, GTS connected and Data List item "Starter SW" selected.


Result:
Proceed to
OK
NG


HINT:

If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter SW".



OK

NG

2.INSPECT ST NO. 1 RELAY (CHECK FOR SHORT CIRCUIT)
2.INSPECT ST NO. 1 RELAY (CHECK FOR SHORT CIRCUIT)
a.

Remove the ST NO. 1 relay from the No. 4 engine room relay block and junction block assembly.


b.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON A
The Data List item "Starter SW" changes from ON to OFF B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST NO. 1 relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

B

REPLACE ST NO. 1 RELAY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
HINT:

The purpose of this step is to check for ST NO. 1 relay terminal voltage under abnormal conditions.


a.
A497288C01
0.063,0.104 0.375,0.302 0.313,0.198 10 false *1 2.313,0.292 2.625,0.49 0.313,0.198 10 false *2
*1 No. 4 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


Remove the ST NO. 1 relay from the No. 4 engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST NO. 1 relay terminal 1 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST NO. 1 relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
a.

Disconnect the park/neutral position switch assembly connector.


b.
A497288C01
0.063,0.104 0.375,0.302 0.313,0.198 10 false *1 2.313,0.292 2.625,0.49 0.313,0.198 10 false *2
*1 No. 4 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


Measure the voltage between ST NO. 1 relay terminal 1 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 1 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 1 relay terminal 1 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
a.

Disconnect the ECM connector.


b.
A497288C01
0.063,0.104 0.375,0.302 0.313,0.198 10 false *1 2.313,0.292 2.625,0.49 0.313,0.198 10 false *2
*1 No. 4 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


Measure the voltage between ST NO. 1 relay terminal 1 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST NO. 1 relay terminal 1 and body ground does not change when the connector is disconnected. A
The voltage between ST NO. 1 relay terminal 1 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU - ST NO. 1 RELAY)

B

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU - ST NO. 1 RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Remove the ST NO. 1 relay from the No. 4 engine room relay block and junction block assembly.



Result:
Proceed to
OK
NG



OK

CHECK ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR