Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P048012  Fan 1 Control Circuit High Circuit Short to Battery  


DESCRIPTION

The electronic control coupling fan can change the oil level as required to control the fan speed to the target value by changing the oil supply valve of the coupling fan from the conventional bimetal type to an electronic control solenoid type.

The electric control coupling fan reduces fan noise and improves fuel economy by reducing the fan speed when not needed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P048012 Fan 1 Control Circuit High Circuit Short to Battery Short circuit in fan control solenoid circuit and power supply circuit (1 trip detection logic).
·

Short in fan control solenoid circuit

·

Fan control solenoid (fluid coupling assembly)

·

ECM


Does not come on SAE Code: P0692

MONITOR DESCRIPTION

The ECM monitors the output voltage while the fan control solenoid is operating.

The fan control solenoid turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the fan control solenoid circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P048012 Start the engine and wait for at 2 minutes or more.

WIRING DIAGRAM

A492900E02
0.604,4.021 1.281,4.271 0.677,0.25 10 false Battery 0.427,3.344 1.49,3.635 1.063,0.292 10 false SUB R/B NO. 1 3.448,1.146 4.125,1.396 0.677,0.25 10 false EFI NO. 1 2.333,2.833 3.031,3.042 0.698,0.208 10 false EFI NO. 2 1.135,2.396 2.229,2.677 1.094,0.281 10 false EFI MAIN NO. 1 2.906,3.042 3.99,3.323 1.083,0.281 10 false EFI MAIN NO. 1 1.51,1.333 2.688,1.594 1.177,0.26 10 false C165 5.854,0.365 6.521,0.792 0.667,0.427 10 false CFDS 5.844,2.708 6.396,2.927 0.552,0.219 10 false MREL 5.479,2.677 5.865,2.948 0.385,0.271 10 false B70 5.427,0.49 5.969,0.729 0.542,0.24 10 false C139 5.531,2.438 5.917,2.708 0.385,0.271 10 false 3 3.104,0.865 3.281,1.094 0.177,0.229 10 false 1 3.083,0.375 3.26,0.604 0.177,0.229 10 false 3 5.542,0.271 5.719,0.5 0.177,0.229 10 false 2 2.625,0.375 3.177,0.594 0.552,0.219 10 false GDFC 2.667,0.875 3.448,1.198 0.781,0.323 10 false EFC+ 6.219,3.302 6.625,3.677 0.406,0.375 10 false ECM 3.719,2.146 3.896,2.375 0.177,0.229 10 false 5 2.927,2.125 3.104,2.354 0.177,0.229 10 false 3 3.729,2.552 3.906,2.781 0.177,0.229 10 false 1 2.917,2.563 3.094,2.792 0.177,0.229 10 false 2 3.833,0.875 4.01,1.104 0.177,0.229 10 false 1 3.427,0.865 3.604,1.094 0.177,0.229 10 false 2 0.438,2.396 1.5,2.688 1.063,0.292 10 false R/B NO. 2 1.51,1.49 3.219,2.354 1.708,0.865 10 false Fan Control Solenoid (Fluid Coupling Assembly) 2.771,2.542 2.948,2.771 0.177,0.229 10 false 2 2.448,2.552 2.625,2.781 0.177,0.229 10 false 1 1.74,2.125 1.917,2.354 0.177,0.229 10 false 2 1.344,2.115 1.521,2.344 0.177,0.229 10 false 1 0.625,2.125 0.802,2.354 0.177,0.229 10 false 1 0.969,2.115 1.146,2.344 0.177,0.229 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY)

OK

2.CHECK HARNESS AND CONNECTOR (FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY) - ECM)

NG

REPLACE FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY) - ECM)

OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P048012)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P048012)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P048012 is output B




A

B