The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the diesel throttle body assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P048718 | Exhaust Gas Recirculation Throttle Control Circuit "A" Low Circuit Current Below Threshold | Both of the following conditions are met for 2.0 seconds:
·
The throttle actuator duty cycle is 80% or higher.
·
The throttle actuator current is less than 0.5 A. (1 trip detection logic) |
·
Open or short in throttle actuator circuit
·
Diesel throttle body assembly
·
ECM |
Comes on | SAE Code: P2141 |
| P048719 | Exhaust Gas Recirculation Throttle Control Circuit "A" High Circuit Current Above Threshold | Either of the following conditions is met for 2.0 seconds:
·
Throttle actuator current of 7 A or higher is detected.
·
The ECM internal circuit temperature of 150°C (302°F) or higher is detected. (1 trip detection logic) |
·
Open or short in throttle actuator circuit
·
Diesel throttle body assembly
·
ECM |
Comes on | SAE Code: P2142 |
| DTC No. | Data List |
|---|---|
| P048718 P048719 |
Diesel Throttle Motor Duty Bank 1 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P048718 P048719 |
Idle the engine for 5 seconds or more |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Remove the diesel throttle body assembly.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL
| *a | Component without harness connected (Diesel Throttle Body Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 - 5 | Always | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the diesel throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C177,C138)Location & Routingewd_type=routing;type=c,c;code=C177,C138 |
||
| C177-6 (M+) - C138-5 (M+) | Always | Below 1 Ω |
| C177-5 (M-) - C138-24 (M-) | Always | Below 1 Ω |
| C177-6 (M+) or C138-5 (M+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C177-5 (M-) or C138-24 (M-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Start the engine.
Idle the engine for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the diesel throttle body assembly.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT