The No. 2 vacuum switching valve assembly (for intake air control valve) is controlled by the ECM, and the opening and closing of the air control valve is performed according to the vacuum applied by the vacuum pump.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P25F812 | Turbocharger/Supercharger Bypass Valve "C" Control Circuit High Circuit Short to Battery | Open or short in the No. 2 vacuum switching valve assembly (for intake air control valve) for 3 seconds. (1 trip detection logic) |
·
Open or short in No. 2 vacuum switching valve assembly (for intake air control valve) circuit
·
No. 2 vacuum switching valve assembly (for intake air control valve)
·
ECM |
Comes on | SAE Code: P25FA |
| P25F814 | Turbocharger/Supercharger Bypass Valve "C" Control Circuit Low Circuit Short to Ground or Open | Open or short in the No. 2 vacuum switching valve assembly (for intake air control valve) for 3 seconds. (1 trip detection logic) |
·
Open or short in No. 2 vacuum switching valve assembly (for intake air control valve) circuit
·
No. 2 vacuum switching valve assembly (for intake air control valve)
·
ECM |
Comes on | SAE Code: P25F9 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P25F812 P25F814 |
Ignition switch ON for 3 seconds or more |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the No. 2 vacuum switching valve assembly (for intake air control valve).
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 vacuum switching valve assembly (for intake air control valve) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C115)Location & Routingewd_type=routing;type=c;code=C115 |
||
| C115-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 vacuum switching valve assembly (for intake air control valve) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C115,C138)Location & Routingewd_type=routing;type=c,c;code=C115,C138 |
||
| C115-2 (AIV1) - C138-49 (ACV) | Always | Below 1 Ω |
| C115-2 (AIV1) or C138-49 (ACV) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
If the voltage at the No. 2 vacuum switching valve assembly (for intake air control valve) connector is not 11 to 14 V, repair or replace the harness and connector between the No. 2 vacuum switching valve assembly (for intake air control valve) and instrument panel junction block assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch to ON and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 2 vacuum switching valve assembly (for intake air control valve).
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT