Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock)
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0473048 FRONT DIFFERENTIAL CARRIER ASSEMBLY(w/o Differential Lock) A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY(w/o Differential Lock)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C459304N01
4.552,2.875 5.583,3.083 1.031,0.208 3.271,2.594 4.188,2.813 0.917,0.219 6.521,2.552 6.896,2.771 0.375,0.219 3.219,2.542 4.25,2.865 1.031,0.323 6.458,2.49 6.969,2.844 0.51,0.354 1.01,1.156 1.927,1.375 0.917,0.219 0.958,1.094 2,1.438 1.042,0.344 0.531,0.74 1.448,0.958 0.917,0.219 0.469,0.688 1.5,1.01 1.031,0.323 1.99,5.49 2.906,5.708 0.917,0.219 1.927,5.438 2.958,5.76 1.031,0.323 3.083,1.833 2.646,0.448 2.646,0.448 1.656,0.448 true 3.396,1.677 2.677,0.188 2.677,0.188 1.813,0.188 false 3.698,2.396 3.823,2.396 3.823,2.396 3.823,1.802 false 3.708,1.063 3.875,1.063 3.875,1.063 4.063,1.448 false 4.365,1.438 3.76,0.49 3.76,0.49 3.635,0.49 true 5.042,1.823 5.25,1.823 5.25,1.823 4.792,1.49 false 5.156,2.208 5.313,2.208 5.313,2.208 5.385,1.354 false 4.969,1.219 4.667,0.469 4.667,0.469 4.552,0.469 false 6.24,1.833 6.448,1.833 6.448,1.833 5.646,1.229 false 6.906,2.667 7.115,2.667 7.115,2.667 6.698,0.917 false 6.302,1.115 6.896,2.188 6.896,2.188 6.781,2.188 false 5.958,0.948 5.958,0.708 5.958,0.708 5.75,0.708 false 5.896,4.896 6.177,4.896 false 5.438,3.354 5.302,3.354 5.302,3.354 4.854,3.844 false 4.365,5.448 4.51,5.448 4.51,5.448 4.177,4.167 false 3.813,4.833 4.01,4.833 4.01,4.833 3.917,4.031 false 3.688,4.438 3.813,4.438 3.813,4.438 3.635,3.865 false 3.146,4.052 3.333,4.052 3.333,4.052 3.271,3.813 false 0.948,5.292 1.49,5.292 false 2.302,3.104 2.448,3.344 2.448,3.344 2.292,3.344 false 2.25,2.469 2.052,2.469 2.052,2.469 2.052,2.76 false 1.76,2.781 1.469,3.219 1.469,3.219 1.323,3.219 false 6.521,0.156 6.823,0.156 false 2.458,3.646 2.625,3.646 2.625,3.646 2.708,3.5 true 4.344,3.229 4.344,2.969 4.344,2.969 4.552,2.969 false 2.573,2.979 2.573,2.708 2.573,2.708 2.917,2.708 false 0.833,1.74 0.833,1.26 0.833,1.26 1,1.26 false 3.938,3.313 4.469,3.313 false 5.125,3.813 5.552,3.813 false 1.375,2.25 1.375,1.646 1.375,1.646 1.542,1.646 false 0.375,2.146 0.375,0.844 0.375,0.844 0.542,0.844 false 0.438,5.01 0.438,5.583 0.438,5.583 1.583,5.583 false 4.667,3.906 4.958,4.115 0.292,0.208 10 false x 2 0.938,1.656 1.385,1.885 0.448,0.229 10 false x 10 2.75,2.833 3.083,3.063 0.333,0.229 10 false x 12 6.521,4.833 6.698,5.042 0.177,0.208 10 false ● 5.5,2.563 5.677,2.771 0.177,0.208 10 false ● 3.042,0.375 3.219,0.583 0.177,0.208 10 false ● 4.323,3.385 4.615,3.594 0.292,0.208 10 false x 2 5.292,0.635 5.469,0.844 0.177,0.208 10 false ● 3.406,0.958 3.719,1.156 0.313,0.198 10 false *1 1.063,3.125 1.375,3.323 0.313,0.198 10 false *2 4.125,5.344 4.438,5.542 0.313,0.198 10 false *2 1.542,5.188 1.854,5.385 0.313,0.198 10 false *3 4.615,2.906 5.583,3.073 0.969,0.167 8 false 6.0 (61, 53 in.*lbf) 3.333,2.625 4.24,2.802 0.906,0.177 8 false 137 (1397, 101) 6.573,2.583 6.917,2.813 0.344,0.229 10 false *T1 1.125,1.177 1.917,1.365 0.792,0.188 8 false 71.5 (729, 53) 2.99,2.615 3.146,2.813 0.156,0.198 10 false ★ 0.542,2.042 0.99,2.271 0.448,0.229 10 false x 2 0.583,0.771 1.438,0.938 0.854,0.167 8 false 130 (1326, 96) 2.031,5.51 2.917,5.688 0.885,0.177 8 false 145 (1479, 107) 0.531,4.76 0.979,4.99 0.448,0.229 10 false x 2 1.698,5.49 1.917,5.719 0.219,0.229 10 false ● 4.708,0.031 6.521,0.333 1.813,0.302 18 false 14 - 17, 33, 34 2.875,3.896 3.167,4.208 0.292,0.313 18 false 1 0.438,0.354 1.719,0.646 1.281,0.292 18 false 11, 23, 26 1.844,1.51 3.073,1.823 1.229,0.313 18 false 13, 21, 28 2.052,3.198 2.344,3.51 0.292,0.313 18 false 2 1.885,3.25 2.063,3.458 0.177,0.208 10 false ● 1.198,3.521 2.458,3.813 1.26,0.292 18 false 12, 22, 27 3.313,4.354 3.49,4.563 0.177,0.208 10 false ● 3.417,4.281 3.708,4.594 0.292,0.313 18 false 2 3.5,4.708 3.792,5.021 0.292,0.313 18 false 3 6.646,4.76 7.115,5.083 0.469,0.323 18 false 37 5.948,3.667 6.24,3.979 0.292,0.313 18 false 9 5.802,3.198 6.094,3.51 0.292,0.313 18 false 8 5.615,2.542 6.438,2.833 0.823,0.292 18 false 18, 36 5.573,2.031 6.854,2.323 1.281,0.292 18 false 19, 32, 35 4.313,2.063 5.177,2.385 0.865,0.323 18 false 24, 29 4.219,0.313 4.51,0.625 0.292,0.313 18 false 6 5.406,0.563 5.844,0.885 0.438,0.323 18 false 31 5.427,1.688 6.25,1.979 0.823,0.292 18 false 20, 30 4.833,1.698 5.125,2.01 0.292,0.313 18 false 4 3.25,0.344 3.688,0.667 0.438,0.323 18 false 25 3.479,2.208 3.771,2.521 0.292,0.313 18 false 5 1.5,0.063 1.792,0.375 0.292,0.313 18 false 7 3.521,3.177 3.958,3.5 0.438,0.323 18 false 10 2.615,2.333 2.906,2.646 0.292,0.313 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSTALL DIFFERENTIAL RING GEAR - - - -
2 INSTALL FRONT DIFFERENTIAL CASE BEARING (INNER) 41311A (Click here) - -
3 INSTALL FRONT DIFFERENTIAL CASE BEARING (OUTER) 41311A (Click here) - -
4 INSTALL FRONT DIFFERENTIAL OIL STORAGE RING 41115F (Click here) - -
5 INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER) 41211B (Click here)
6 INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING (OUTER) 41211A (Click here)
7 INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER) 41211B (Click here) - -
8 INSTALL FRONT DIFFERENTIAL CARRIER STRAIGHT PIN 41111D (Click here) - -
9 INSTALL FRONT DIFFERENTIAL UNION - (Click here) - -
10 INSTALL FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR 41183C - - -
11 INSTALL DIFFERENTIAL DRIVE PINION - - - -
12 INSTALL FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY 41301L - - -
13 INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER - - - -
14 ADJUST DIFFERENTIAL DRIVE PINION PRELOAD - (Click here) - -
15 ADJUST BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION - (Click here) - -
16 INSPECT TOTAL PRELOAD - (Click here) - -
17 ADJUST TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION - - - -
18 REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT 41204E (Click here) - -
19 REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY 41204D (Click here) - -
20 REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER 41214C - - -
21 REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER - - - -
22 REMOVE FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY 41301L - - -
23 REMOVE DIFFERENTIAL DRIVE PINION - - - -
24 REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING (INNER) 41211A (Click here) - -
25 INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER 41231F - - -
26 INSTALL DIFFERENTIAL DRIVE PINION - - - -
27 INSTALL FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY 41301L - -
28 INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER - (Click here) - -
29 INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING (INNER) 41211A - - -
30 INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER 41214C - - -
31 INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL - (Click here) - -
32 INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY 41204D (Click here) - -
33 INSPECT TOTAL PRELOAD - - - -
34 INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH - (Click here) - -
35 INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY 41204D (Click here) - -
36 STAKE DRIVE PINION NUT - - - -
37 INSTALL FRONT DRIVE SHAFT OIL SEAL LH 43420H (Click here) - -

*1 DRIVE PINION WASHER *2 PLATE WASHER
*3 FRONT DIFFERENTIAL SUPPORT ASSEMBLY - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

MP grease
V100136

Hypoid gear oil
● Non-reusable part ★ Precoated part
*T1 451 (4599, 333) or less - -

C459305N03
3.833,4.771 4.573,5.042 0.74,0.271 3.76,4.688 4.656,5.135 0.896,0.448 0.969,0.906 1.083,0.333 1.083,0.333 1.354,0.333 true 5.458,3.469 5.625,2.948 5.625,2.948 5.896,2.948 true 3.573,2.5 3.75,1.99 3.75,1.99 4.021,1.99 true 2.573,1.823 2.76,1.135 2.76,1.135 2.948,1.135 true 2,1.583 2.167,0.885 2.167,0.885 2.438,0.885 true 1.667,1.323 1.771,0.677 1.771,0.677 2.042,0.677 true 4.573,4.917 5.177,4.917 false 6.26,2.802 6.74,3.156 0.479,0.354 18 false 41 1.802,0.208 2.24,0.542 0.438,0.333 18 false 40 1.656,0.24 1.844,0.448 0.188,0.208 10 false ● 4.49,1.844 4.938,2.177 0.448,0.333 18 false 39 3.354,0.958 3.771,1.323 0.417,0.365 18 false 38 2.115,0.573 2.406,0.802 0.292,0.229 10 false ● 5.375,4.719 5.854,4.958 0.479,0.24 10 false x 4 3.896,4.833 4.594,5.021 0.698,0.188 8 false 73 (744, 54) 3.531,4.823 3.719,5.031 0.188,0.208 10 false ● 2.5,0.781 2.75,1.01 0.25,0.229 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

38 INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH - (Click here) - -
39 INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH 41304F - - -
40 INSTALL FRONT DRIVE SHAFT OIL SEAL RH 43410M (Click here) - -
41 INSTALL DIFFERENTIAL EXTENSION FLANGE TUBE 41321 (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100135

MP Grease
● Non-reusable part - -

PROCEDURE

Hide 1.INSTALL DIFFERENTIAL RING GEAR

a.
C457961C01
3.74,0.927 4.688,1.302 4.688,1.302 3.729,1.031 true 4.771,1.229 5.104,1.458 0.333,0.229 10 false *a 0.188,0.083 0.854,0.448 0.667,0.365 18 false i - vi
*a Matchmark - -


i.

Clean the contact surface of the differential case and differential ring gear.


ii.

Heat the differential ring gear in boiling water that is approximately 100°C (212°F).


iii.

Carefully remove the differential ring gear from the boiling water.


iv.

After the moisture on the differential ring gear has completely evaporated, quickly install the differential ring gear to the differential case.


v.

Align the matchmarks on the differential ring gear and differential case.


vi.

After the ring gear cools down, apply thread lock adhesive to the 12 set bolts and install them.

Thread lock:

Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent


Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)



Hide 41311A 2.INSTALL FRONT DIFFERENTIAL CASE BEARING (INNER)

a.
C457962N02
4.167,0.771 4.865,0.573 4.865,0.573 5.031,0.573 true 4.135,1.479 4.802,1.229 4.802,1.229 5,1.229 true 2.208,0.063 2.521,0.396 0.313,0.333 18 false i 5.073,0.479 5.573,0.708 0.5,0.229 10 false SST 5.063,1.125 5.563,1.354 0.5,0.229 10 false SST

i.

Using SST and a press, press the 2 front differential case bearings (inner) onto the differential case.

SST
09950-60011  (09951-00520, 09951-00610)
09950-70010  (09951-07150)



Hide 41311A 3.INSTALL FRONT DIFFERENTIAL CASE BEARING (OUTER)

Z101186

HINT:

When replacing the 2 front differential case bearings, install the thinnest washer to each front differential case bearing. When reusing the front differential case bearings, install a new plate washer of the same thickness as the one that was removed to each front differential case bearing.



a.
C457963C01
1.448,0.99 1.615,0.229 1.615,0.229 1.823,0.229 true 5.26,1.292 5.583,1.552 5.583,1.552 5.792,1.552 true 3.031,0.688 3.281,1.344 3.281,1.344 3.49,1.344 true 6.063,0.802 6.313,1.458 6.313,1.458 6.521,1.458 true 1.885,0.167 2.25,0.396 0.365,0.229 10 false SST 5.813,1.448 6.177,1.677 0.365,0.229 10 false SST 3.969,0.052 4.635,0.375 0.667,0.323 18 false iii, iv 0.396,0.042 1.094,0.344 0.698,0.302 18 false i, ii 3.531,1.26 3.844,1.458 0.313,0.198 10 false *1 6.563,1.375 6.875,1.573 0.313,0.198 10 false *1
*1 Plate Washer - -


i.

Install a new plate washer to the shaft bearing retainer.


ii.

Using SST and a press, press in the front differential case bearing (outer) to the differential side bearing retainer.

SST
09950-60021  (09951-00910)
09950-70010  (09951-07150)


iii.

Install a new plate washer to the differential carrier.


iv.

Using SST and a press, press in the front differential case bearing (outer) to the differential carrier.

SST
09950-60021  (09951-00910)
09950-70010  (09951-07150)



Hide 41115F 4.INSTALL FRONT DIFFERENTIAL OIL STORAGE RING

a.
C458510N01
3.865,1.323 3.969,0.885 3.969,0.885 4.833,0.885 false 0.396,0.031 0.719,0.385 0.323,0.354 18 false i 4.49,1.156 4.792,1.375 0.302,0.219 10 false (A) 4.896,0.781 5.354,0.979 0.458,0.198 10 false SST

i.

Using SSTand hammer, install the front differential oil storage ring.

NOTICE:

Install the differential carrier assembly so that front differential oil storage ring does not overlap the oil passage.


SST
09950-60021  (09951-00710)

Standard front differential oil storage ring depth (A):

66.4 to 68.4 mm (2.615 to 2.692 in.)




Hide 41211B 5.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER)

a.
C457964C01
4.698,0.75 5.083,0.75 true 5.531,0.656 6.104,0.656 true 5.521,0.979 6.094,0.979 true 4.688,1.104 4.927,1.104 4.927,1.104 5.177,0.792 true 4.521,0.677 4.771,0.885 0.25,0.208 10 false *1 3.021,0.625 3.333,0.781 0.313,0.156 10 false *a 1.052,1.458 1.365,1.615 0.313,0.156 10 false *b 6.135,0.552 6.521,0.792 0.385,0.24 10 false SST 6.167,0.896 6.573,1.135 0.406,0.24 10 false SST 0.406,0.042 0.969,0.427 0.563,0.385 18 false i 4.51,1.031 4.76,1.24 0.25,0.208 10 false *2
*1 Front Drive Pinion Rear Tapered Roller Bearing (Outer) *2 Drive Pinion Washer
*a Turn *b Hold


i.

Using SST, install the drive pinion washer and front drive pinion rear tapered roller bearing (outer).

SST
09950-60021  (09951-00720, 09951-00890)
09950-70010  (09951-07150)

HINT:

First, install a drive pinion plate washer that has the same thickness as the removed drive pinion plate washer. After checking the tooth contact pattern, replace the drive pinion plate washer with one of a different thickness if necessary.




Hide 41211A 6.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING (OUTER)

a.
C457965C01
4.698,1 5.083,1 true 5.5,0.604 6.073,0.604 true 5.521,1.073 6.094,1.073 true 4.521,0.906 4.771,1.115 0.25,0.208 10 false *1 3.021,0.625 3.333,0.781 0.313,0.156 10 false *a 1.052,1.458 1.365,1.615 0.313,0.156 10 false *b 6.146,0.51 6.531,0.75 0.385,0.24 10 false SST 6.156,0.99 6.563,1.229 0.406,0.24 10 false SST 0.417,0.063 0.813,0.344 0.396,0.281 18 false i
*1 Front Drive Pinion Front Tapered Roller Bearing (Outer) - -
*a Turn *b Hold


i.

Using SST, install the front drive pinion front tapered roller bearing (outer).

SST
09950-60021  (09951-00720, 09951-00890)



Hide 41211B 7.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER)

a.
C459314N01
3.833,0.917 4.667,0.917 true 3.833,1.417 4.25,1.417 4.25,1.417 4.25,0.917 true 2.177,0.104 2.521,0.438 0.344,0.333 18 false i 4.708,0.823 5.198,1.052 0.49,0.229 10 false SST

i.

Using SST and a press, press the front drive pinion front tapered roller bearing (inner) onto the differential drive pinion.

SST
09950-60011  (09951-00610)
09308-14010  



Hide 41111D 8.INSTALL FRONT DIFFERENTIAL CARRIER STRAIGHT PIN

a.
C459288N01
2.542,0.042 2.958,0.375 0.417,0.333 18 false i 4.625,0.74 4.813,0.938 0.188,0.198 10 false A

i.

Using a plastic-faced hammer, tap in the 2 straight pins until the protrusion height shown in the illustration is within the specification.

Standard height (A):

9.5 to 10.0 mm (0.374 to 0.393 in.)




Hide 9.INSTALL FRONT DIFFERENTIAL UNION

a.
C459372C01
5.781,1.042 6.094,1.24 0.313,0.198 10 false *a 0.417,0.042 0.74,0.333 0.323,0.292 18 false i
*a 36 to 42° - -


i.

Install the front differential union.

HINT:

Make sure that the tabs of the front differential union are positioned within the area shown in the illustration.




Hide 41183C 10.INSTALL FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

Hide 11.INSTALL DIFFERENTIAL DRIVE PINION

Hide 41301L 12.INSTALL FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 13.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

Z101186

NOTICE:

After fully tightening all bolts, check that all bolts are tightened to the specified torque.



a.
C463194N01
4.854,0.802 5.031,1.01 0.177,0.208 10 false A 4.76,0.375 4.938,0.583 0.177,0.208 10 false A 4.354,0.021 4.531,0.229 0.177,0.208 10 false A 3.646,0 3.823,0.208 0.177,0.208 10 false A 3.167,0.021 3.344,0.229 0.177,0.208 10 false A 2.667,0.083 2.844,0.292 0.177,0.208 10 false A 2.479,1.208 2.656,1.417 0.177,0.208 10 false A 2.698,1.24 2.875,1.448 0.177,0.208 10 false A 3.656,1.573 3.833,1.781 0.177,0.208 10 false A 4.313,1.573 4.49,1.781 0.177,0.208 10 false A 3.021,1.552 3.198,1.76 0.177,0.208 10 false B 2.885,1.427 3.063,1.635 0.177,0.208 10 false B

i.

Install the differential cross shaft bearing retainer and differential carrier assembly with the 10 bolts (A).

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


ii.

Install the differential cross shaft bearing retainer and differential carrier assembly with the 2 bolts (B).

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)



Hide 14.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
C457967C01
4.615,0.521 5.031,0.521 true 0.938,2.625 1.188,2.625 1.188,2.625 1.26,2.833 true 4.24,0.427 4.635,0.656 0.396,0.229 10 false SST 6.229,0.76 6.49,1.01 0.26,0.25 10 false *a 4.594,1.354 4.854,1.604 0.26,0.25 10 false *b 0.76,3.219 1.021,3.469 0.26,0.25 10 false *b 3.406,3.323 3.667,3.573 0.26,0.25 10 false *a 0.531,2.531 0.969,2.729 0.438,0.198 10 false SST 4.156,0.083 4.75,0.625 0.594,0.542 18 false ii, iii 4.115,2.031 4.469,2.365 0.354,0.333 18 false v 0.365,2 0.719,2.333 0.354,0.333 18 false iv 0.385,0.052 0.667,0.365 0.281,0.313 18 false i
*a Turn *b Hold


i.

Install the front drive pinion front radial ball bearing (inner) and front differential drive pinion oil slinger.


ii.

Using SST, install the front drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



iii.

Adjust the differential drive pinion preload by tightening the front drive pinion companion flange nut.


iv.

Using SST to hold the front drive pinion companion flange sub-assembly with dust deflector in place, tighten the front drive pinion companion flange nut.

SST
09330-00021  (09330-00030)

Limit torque value:

451 N*m (4599 kgf*cm, 333 ft.*lbf) or less


NOTICE:
·

As there is no spacer, tighten the nut a little at a time. Be careful not to overtighten it.

·

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.




v.

Using a torque wrench, measure the preload.

Standard Preload (Starting Torque):
Item Specified Condition
New bearing 3.40 to 3.90 N*m (35 to 39 kgf*cm, 31 to 34 in.*lbf)
Reused bearing 3.25 to 3.57 N*m (34 to 36 kgf*cm, 29 to 31 in.*lbf)


NOTICE:
·

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.

·

Record the differential drive pinion preload for the total preload measurement.





Hide 15.ADJUST BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION

a.
C457968N01
2.49,0.698 2.708,0.698 2.708,0.698 3.292,1.073 false 2.292,0.052 2.854,0.427 0.563,0.375 18 false i 2.177,0.604 2.552,0.823 0.375,0.219 10 false SST

i.

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-33010  

Standard backlash:

0.17 to 0.27 mm (0.00670 to 0.0106 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness ofthe washers on both sides by an equal amount.

HINT:
·

There should be no clearance between the plate washer and differential case.

·

Make sure that there is ring gear backlash.



Standard Washer Thickness:
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-65033 1.49 to 1.51 mm ( 0.0587 to 0.0594 in.) 90564-65055 1.93 to 1.95 mm ( 0.0760 to 0.0767 in.)
90564-65034 1.51 to 1.53 mm ( 0.0595 to 0.0602 in.) 90564-65056 1.95 to 1.97 mm ( 0.0768 to 0.0775 in.)
90564-65035 1.53 to 1.55 mm ( 0.0603 to 0.0610 in.) 90564-65057 1.97 to 1.99 mm ( 0.0776 to 0.0783 in.)
90564-65036 1.55 to 1.57 mm ( 0.0611 to 0.0618 in.) 90564-65058 1.99 to 2.01 mm ( 0.0784 to 0.0791 in.)
90564-65037 1.57 to 1.59 mm ( 0.0619 to 0.0625 in.) 90564-65059 2.01 to 2.03 mm ( 0.0792 to 0.0799 in.)
90564-65038 1.59 to 1.61 mm ( 0.0626 to 0.0633 in.) 90564-65060 2.03 to 2.05 mm ( 0.0800 to 0.0807 in.)
90564-65039 1.61 to 1.63 mm ( 0.0634 to 0.0641 in.) 90564-65061 2.05 to 2.07 mm ( 0.0808 to 0.0814 in.)
90564-65040 1.63 to 1.65 mm ( 0.0642 to 0.0649 in.) 90564-65062 2.07 to 2.09 mm ( 0.0815 to 0.0822 in.)
90564-65041 1.65 to 1.67 mm ( 0.0650 to 0.0657 in.) 90564-65063 2.09 to 2.11 mm ( 0.0823 to 0.0830 in.)
90564-65042 1.67 to 1.69 mm ( 0.0658 to 0.0665 in.) 90564-65064 2.11 to 2.13 mm ( 0.0831 to 0.0838 in.)
90564-65043 1.69 to 1.71 mm ( 0.0666 to 0.0673 in.) 90564-65065 2.13 to 2.15 mm ( 0.0839 to 0.0846 in.)
90564-65044 1.71 to 1.73 mm ( 0.0674 to 0.0681 in.) 90564-65066 2.15 to 2.17 mm ( 0.0847 to 0.0854 in.)
90564-65045 1.73 to 1.75 mm ( 0.0682 to 0.0688 in.) 90564-65067 2.17 to 2.19 mm ( 0.0855 to 0.0862 in.)
90564-65046 1.75 to 1.77 mm ( 0.0689 to 0.0696 in.) 90564-65068 2.19 to 2.21 mm ( 0.0863 to 0.0870 in.)
90564-65047 1.77 to 1.79 mm ( 0.0697 to 0.0704 in.) 90564-65069 2.21 to 2.23 mm ( 0.0871 to 0.0877 in.)
90564-65048 1.79 to 1.81 mm ( 0.0705 to 0.0712 in.) 90564-65070 2.23 to 2.25 mm ( 0.0878 to 0.0885 in.)
90564-65049 1.81 to 1.83 mm ( 0.0713 to 0.0720 in.) 90564-65071 2.25 to 2.27 mm ( 0.0886 to 0.0893 in.)
90564-65050 1.83 to 1.85 mm ( 0.0721 to 0.0728 in.) 90564-65072 2.27 to 2.29 mm ( 0.0894 to 0.0901 in.)
90564-65051 1.85 to 1.87 mm ( 0.0729 to 0.0736 in.) 90564-65073 2.29 to 2.31 mm ( 0.0902 to 0.0909 in.)
90564-65052 1.87 to 1.89 mm ( 0.0737 to 0.0744 in.) 90564-65074 2.31 to 2.33 mm ( 0.0910 to 0.0917 in.)
90564-65053 1.89 to 1.91 mm ( 0.0745 to 0.0751 in.) 90564-65075 2.33 to 2.35 mm ( 0.0918 to 0.0925 in.)
90564-65054 1.91 to 1.93 mm ( 0.0752 to 0.0759 in.) - -




Hide 16.INSPECT TOTAL PRELOAD

a.
C457969N01
0.448,0.063 0.729,0.417 0.281,0.354 18 false i

i.

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload (Starting Torque):
Reduction Ratio Item Specified Condition
3.307 New bearing 4.61 to 5.89 N*m (48 to 60 kgf*cm, 41 to 52 in.*lbf)
Reused bearing 4.43 to 5.52 N*m (46 to 56 kgf*cm, 40 to 48 in.*lbf)
4.300 New bearing 4.33 to 5.43 N*m (45 to 55 kgf*cm, 39 to 48 in.*lbf)
Reused bearing 4.16 to 5.07 N*m (43 to 51 kgf*cm, 44 to xx in.*lbf)


If necessary, disassemble and inspect the differential.



Hide 17.ADJUST TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.
C463196N01
0.094,0.073 0.688,0.406 0.594,0.333 18 false i - ii 3.5,0.063 4.281,0.406 0.781,0.344 18 false iii - iv 4.24,0.125 4.396,0.323 0.156,0.198 10 false A 4.479,0.01 4.635,0.208 0.156,0.198 10 false A 5.302,0 5.458,0.198 0.156,0.198 10 false A 5.958,0.042 6.115,0.24 0.156,0.198 10 false A 6.375,0.385 6.531,0.583 0.156,0.198 10 false A 6.448,0.76 6.604,0.958 0.156,0.198 10 false A 5.906,1.563 6.063,1.76 0.156,0.198 10 false A 5.323,1.583 5.479,1.781 0.156,0.198 10 false A 4.385,1.24 4.542,1.438 0.156,0.198 10 true A 4.094,1.135 4.25,1.333 0.156,0.198 10 true A 4.51,1.427 4.667,1.625 0.156,0.198 10 true B 4.688,1.542 4.844,1.74 0.156,0.198 10 true B

i.

Remove the differential case bearing retainer and differential case.


ii.

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


iii.

Install the differential case and differential case bearing retainer.

Torque:
Bolt A : 71.5 N*m (729 kgf*cm, 53 ft.*lbf)
Bolt B : 130 N*m (1326 kgf*cm, 96 ft.*lbf)

NOTICE:

After fully tightening all bolts, check that all bolts are tightened to the specified torque.



iv.

Hold the companion flange firmly in place and rotate the ring gear in both directions.



b.
C116070C01
1.583,1.906 1.833,2.104 0.25,0.198 10 false *a 2.875,0.594 3.104,0.75 0.229,0.156 10 false *b 2.771,3.448 3,3.615 0.229,0.167 10 false *e 4.969,0.552 5.177,0.729 0.208,0.177 10 false *c 5.073,3.427 5.271,3.604 0.198,0.177 10 false *f 3.688,4.677 3.958,4.917 0.271,0.24 10 false *g 3.677,2.073 3.917,2.25 0.24,0.177 10 false *d 0.177,0.115 0.5,0.49 0.323,0.375 18 true i
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear (*e, *f) - -


i.

Inspect the tooth contact pattern.

Standard Washer Thickness:
Drive Pinion Side:
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-68104 1.815 to 1.835 mm ( 0.0715 to 0.0722 in.) 90564-68114 2.065 to 2.085 mm ( 0.0813 to 0.0820 in.)
90564-68105 1.84 to 1.86 mm ( 0.0725 to 0.0732 in.) 90564-68115 2.09 to 2.11 mm ( 0.0823 to 0.0830 in.)
90564-68106 1.865 to 1.885 mm ( 0.0735 to 0.0742 in.) 90564-68116 2.115 to 2.135 mm ( 0.0833 to 0.0840 in.)
90564-68107 1.89 to 1.91 mm ( 0.0745 to 0.0751 in.) 90564-68117 2.14 to 2.16 mm ( 0.0843 to 0.0850 in.)
90564-68108 1.915 to 1.935 mm ( 0.0754 to 0.0761 in.) 90564-68118 2.165 to 2.185 mm ( 0.0853 to 0.0860 in.)
90564-68109 1.94 to 1.96 mm ( 0.0764 to 0.0771 in.) 90564-68119 2.19 to 2.21 mm ( 0.0863 to 0.0870 in.)
90564-68110 1.965 to 1.985 mm ( 0.0774 to 0.0781 in.) 90564-68120 2.215 to 2.235 mm ( 0.0873 to 0.0879 in.)
90564-68111 1.99 to 2.01 mm ( 0.0784 to 0.0791 in.) 90564-68121 2.24 to 2.26 mm ( 0.0882 to 0.0889 in.)
90564-68112 2.015 to 2.035 mm ( 0.0794 to 0.0801 in.) 90564-68122 2.265 to 2.285 mm ( 0.0892 to 0.0899 in.)
90564-68113 2.04 to 2.06 mm ( 0.0804 to 0.0811 in.) - -

Side Gear Side:
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-65033 1.49 to 1.51 mm ( 0.0587 to 0.0594 in.) 90564-65055 1.93 to 1.95 mm ( 0.0760 to 0.0767 in.)
90564-65034 1.51 to 1.53 mm ( 0.0595 to 0.0602 in.) 90564-65056 1.95 to 1.97 mm ( 0.0768 to 0.0775 in.)
90564-65035 1.53 to 1.55 mm ( 0.0603 to 0.0610 in.) 90564-65057 1.97 to 1.99 mm ( 0.0776 to 0.0783 in.)
90564-65036 1.55 to 1.57 mm ( 0.0611 to 0.0618 in.) 90564-65058 1.99 to 2.01 mm ( 0.0784 to 0.0791 in.)
90564-65037 1.57 to 1.59 mm ( 0.0619 to 0.0625 in.) 90564-65059 2.01 to 2.03 mm ( 0.0792 to 0.0799 in.)
90564-65038 1.59 to 1.61 mm ( 0.0626 to 0.0633 in.) 90564-65060 2.03 to 2.05 mm ( 0.0800 to 0.0807 in.)
90564-65039 1.61 to 1.63 mm ( 0.0634 to 0.0641 in.) 90564-65061 2.05 to 2.07 mm ( 0.0808 to 0.0814 in.)
90564-65040 1.63 to 1.65 mm ( 0.0642 to 0.0649 in.) 90564-65062 2.07 to 2.09 mm ( 0.0815 to 0.0822 in.)
90564-65041 1.65 to 1.67 mm ( 0.0650 to 0.0657 in.) 90564-65063 2.09 to 2.11 mm ( 0.0823 to 0.0830 in.)
90564-65042 1.67 to 1.69 mm ( 0.0658 to 0.0665 in.) 90564-65064 2.11 to 2.13 mm ( 0.0831 to 0.0838 in.)
90564-65043 1.69 to 1.71 mm ( 0.0666 to 0.0673 in.) 90564-65065 2.13 to 2.15 mm ( 0.0839 to 0.0846 in.)
90564-65044 1.71 to 1.73 mm ( 0.0674 to 0.0681 in.) 90564-65066 2.15 to 2.17 mm ( 0.0847 to 0.0854 in.)
90564-65045 1.73 to 1.75 mm ( 0.0682 to 0.0688 in.) 90564-65067 2.17 to 2.19 mm ( 0.0855 to 0.0862 in.)
90564-65046 1.75 to 1.77 mm ( 0.0689 to 0.0696 in.) 90564-65068 2.19 to 2.21 mm ( 0.0863 to 0.0870 in.)
90564-65047 1.77 to 1.79 mm ( 0.0697 to 0.0704 in.) 90564-65069 2.21 to 2.23 mm ( 0.0871 to 0.0877 in.)
90564-65048 1.79 to 1.81 mm ( 0.0705 to 0.0712 in.) 90564-65070 2.23 to 2.25 mm ( 0.0878 to 0.0885 in.)
90564-65049 1.81 to 1.83 mm ( 0.0713 to 0.0720 in.) 90564-65071 2.25 to 2.27 mm ( 0.0886 to 0.0893 in.)
90564-65050 1.83 to 1.85 mm ( 0.0721 to 0.0728 in.) 90564-65072 2.27 to 2.29 mm ( 0.0894 to 0.0901 in.)
90564-65051 1.85 to 1.87 mm ( 0.0729 to 0.0736 in.) 90564-65073 2.29 to 2.31 mm ( 0.0902 to 0.0909 in.)
90564-65052 1.87 to 1.89 mm ( 0.0737 to 0.0744 in.) 90564-65074 2.31 to 2.33 mm ( 0.0910 to 0.0917 in.)
90564-65053 1.89 to 1.91 mm ( 0.0745 to 0.0751 in.) 90564-65075 2.33 to 2.35 mm ( 0.0918 to 0.0925 in.)
90564-65054 1.91 to 1.93 mm ( 0.0752 to 0.0759 in.) - -


If the teeth are not engaged properly, use the following chart to select the appropriate washer for correction.



Hide 41204E 18.REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT

Z101186

Click here(Click here)

Hide 41204D 19.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 41214C 20.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 21.REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

Hide 41301L 22.REMOVE FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41211A 24.REMOVE REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING (INNER)

Z101186

Click here(Click here)

Hide 41231F 25.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C457972


Hide 26.INSTALL DIFFERENTIAL DRIVE PINION

Hide 41301L 27.INSTALL FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 28.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

Z101186

NOTICE:

After fully tightening all bolts, check that all bolts are tightened to the specified torque.



a.
C459299C01
4.479,0.708 4.771,0.323 4.771,0.323 4.938,0.323 true 4.99,0.208 5.271,0.469 0.281,0.26 10 false *a 0.438,0.063 1.25,0.479 0.813,0.417 18 false i - iii
*a Seal Packing - -


i.

Remove any old seal packing material from the differential side bearing retainer.

NOTICE:

Do not drop oil on the contact surfaces of the differential carrier and differential side bearing retainer.



ii.

Clean residual seal packing material on the contact surface using gasoline or alcohol.


iii.

Apply seal packing to the differential side bearing retainer as shown in the illustration.

Seal packing:

Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent


HINT:

Install the differential side bearing retainer within 3 minutes after applying seal packing.




b.
C463193N01
0.458,0.031 1.115,0.344 0.656,0.313 18 false i - iii 4.698,0.625 4.875,0.833 0.177,0.208 10 false A 4.563,0.344 4.74,0.552 0.177,0.208 10 false A 4.271,0.052 4.448,0.26 0.177,0.208 10 false A 3.646,0 3.823,0.208 0.177,0.208 10 false A 3.167,0.021 3.344,0.229 0.177,0.208 10 false A 2.667,0.083 2.844,0.292 0.177,0.208 10 false A 2.479,1.208 2.656,1.417 0.177,0.208 10 false A 2.698,1.24 2.875,1.448 0.177,0.208 10 false A 3.573,1.573 3.75,1.781 0.177,0.208 10 false A 4.385,1.51 4.594,1.75 0.208,0.24 10 false C 3.021,1.552 3.198,1.76 0.177,0.208 10 false B 2.885,1.427 3.063,1.635 0.177,0.208 10 false B 4.083,1.573 4.26,1.781 0.177,0.208 10 false A 4.667,0.906 4.875,1.146 0.208,0.24 10 false C

i.

Install the differential cross shaft bearing retainer and differential carrier assembly with the 10 bolts (A).

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


ii.

Install the differential cross shaft bearing retainer and differential carrier assembly with the 2 new bolts (B).

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)


iii.

Install the differential cross shaft bearing retainer and differential support with the 2 new bolts (C).

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)



Hide 41211A 29.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING (INNER)

a.
C459278


Hide 41214C 30.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 31.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL

Z101186

Click here(Click here)

Hide 41204D 32.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C459318C01
2.083,0.917 2.75,1.333 2.75,1.333 2.917,1.333 true 0.74,0 1.375,0.354 0.635,0.354 18 true i, ii 3.99,0.01 4.625,0.365 0.635,0.354 18 true iii 6.677,1.51 6.99,1.667 0.313,0.156 10 false *a 4.281,1.26 4.594,1.417 0.313,0.156 10 false *b 2.823,0.729 3.135,0.885 0.313,0.156 10 false *a 0.51,0.938 0.823,1.094 0.313,0.156 10 false *b 3,1.219 3.51,1.458 0.51,0.24 10 false SST
*a Turn *b Hold


i.

Using SST, install the front drive pinion companion flange sub-assembly.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



ii.

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.


iii.

Using SST to hold the companion flange, install a new front drive pinion companion flange nut.

SST
09330-00021  

Limit torque value:

451 N*m (4599 kgf*cm, 333 ft.*lbf) or less




Hide 33.INSPECT TOTAL PRELOAD

a.
C457974N01
0.135,0.083 0.417,0.438 0.281,0.354 18 false i

i.

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload (Starting Torque):
Reduction Ratio Item Specified Condition
3.307 New bearing 5.04 to 6.32 N*m (52 to 64 kgf*cm, 45 to 55 in.*lbf)
Reused bearing 4.86 to 5.95 N*m (50 to 60 kgf*cm, 44 to 52 in.*lbf)
4.300 New bearing 4.76 to 5.86 N*m (49 to 59 kgf*cm, 43 to 51 in.*lbf)
Reused bearing 4.59 to 5.50 N*m (47 to 56 kgf*cm, 41 to 48 in.*lbf)


If necessary, disassemble and inspect the differential.



Hide 34.INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

a.
C457975N01
2.583,0.75 2.75,0.75 2.75,0.75 3.292,1.073 true 2.167,0.052 2.448,0.406 0.281,0.354 18 false i 2.219,0.677 2.667,1 0.448,0.323 10 false SST

i.

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-32011  

Standard backlash:

0.17 to 0.27 mm (0.00670 to 0.0106 in.)


If the backlash is not within the specification, adjust the side bearing preload.



Hide 41204D 35.INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 36.STAKE FRONT DRIVE PINION COMPANION FLANGE NUT

a.
C457989


Hide 43420H 37.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

Z101186

Click here(Click here)

Hide 38.INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH

a.
C457957N01
2.188,0.531 2.521,0.531 true 2.573,0.438 3.031,0.635 0.458,0.198 10 false SST 0.698,0.031 1.188,0.365 0.49,0.333 18 false i 3.719,0.031 4.208,0.365 0.49,0.333 18 false ii

i.

Using SST and a press, press in the front differential side gear shaft bearing RH.

SST
09223-00010  


ii.

Using a snap ring expander, install the snap ring.



Hide 41304F 39.INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

a.
C457958N01
0.573,0.104 1.083,0.448 0.51,0.344 18 false i, ii

i.

Install the differential side gear shaft sub-assembly RH to the front differential tube assembly.


ii.

Using a snap ring pliers, install a new snap ring.

HINT:

Install the snap ring securely.




Hide 43410M 40.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

Z101186

Click here(Click here)

Hide 41321 41.INSTALL DIFFERENTIAL EXTENSION FLANGE TUBE

a.
C457977C01
3.51,1.458 3.302,1.458 3.302,1.458 2.688,1.042 true 3.594,1.344 3.865,1.563 0.271,0.219 10 false *a 0.698,0.042 1.302,0.396 0.604,0.354 18 false i - iv 4.094,0.063 4.74,0.469 0.646,0.406 18 false v, vi
*a Seal Packing - -


i.

Remove any old seal packing material on the contact surfaces of the differential and clutch case.

NOTICE:

Do not drop oil on the contact surfaces of the differential and clutch case.



ii.

Clean residual seal packing material on the contact surface using gasoline or alcohol.


iii.

Apply seal packing to the differential as shown in the illustration.

Seal packing:

Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent


HINT:

Install the differential tube within 3 minutes after applying seal packing.



iv.

Install the front differential tube to the differential.


v.

Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.


vi.

Install the 4 bolts.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)